| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
staging: octeon: add missing napi_disable in cvm_oct_rx_shutdown
cvm_oct_rx_shutdown calls free_irq and netif_napi_del without
disabling the napi instance first. As the free_irq only waits
for completion of hard interrupt handlers, the napi poll
function could still be active. If cvm_oct_remove proceeds to
free the plat structure (which holds the NAPI instances), the
active poll function will access freed memory, resulting in a
use-after-free crash. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/bnxt_re: Validate udata before executing commands
The destroy callbacks currently zero the udata output after tearing down
driver resources. If the userspace access fails, uverbs preserves the
uobject and allows the destroy callback to run again, even though the
driver resource has already been freed.
Call ib_no_udata_io() before teardown so udata failures are detected
while the resource is still intact, then return success after teardown
completes.
As part of this change, move ib_respond_empty_udata() to the start of
the create and modify flows. While this is not strictly required for
general create flows, as the core layer unwinds uobjects on failure, it
is necessary for create AH. In _rdma_create_ah(), the HW object is
otherwise leaked. |
| In the Linux kernel, the following vulnerability has been resolved:
phy: renesas: phy-rcar-gen3-usb2: Fix devm action registration for disabled VBUS regulator
devm_regulator_get_exclusive() initialises the regulator with
enable_count = 1, requiring the consumer to disable it before release.
The devm disable action was previously only registered when the caller
explicitly requested enable, so when the regulator was left in its initial
enabled state without an explicit enable call, the cleanup path skipped
decrementing enable_count, triggering a WARN_ON during regulator
release on device removal.
Fix this by always registering the devm disable action based on the actual
enabled state via regulator_is_enabled(), regardless of whether the
caller requested an explicit enable. This covers both the explicitly
enabled case and the initial state set by devm_regulator_get_exclusive(). |
| In the Linux kernel, the following vulnerability has been resolved:
perf/x86/intel/pt: Fix stop/start with no update
If pt_event_stop() is called without PERF_EF_UPDATE flag, then
perf_aux_output_end() is not called. A subsequent call to pt_event_start()
will call perf_aux_output_begin() again which violates the rule against
nesting and triggers a WARNING in perf_aux_output_begin().
Originally, pt_event_stop() was never called without PERF_EF_UPDATE,
because the only code paths to do so are from event overflow, and Intel PT
does not do that.
However the introduction of group throttling by commit 9734e25fbf5ae
("perf: Fix the throttle logic for a group") meant that an Intel PT event
could be throttled if it was part of a group. Throttling calls PMU
->stop() / ->start() callbacks without flags.
An example is when AUX area sampling is used. The following commands
hit the issue:
echo 10000 > /proc/sys/kernel/perf_event_max_sample_rate
perf record -F32000 --aux-sample -e '{intel_pt//u,cycles:u}' \
-- bash -c 'for i in `seq 1 100000` ; do true ; done'
Use PERF_HES_UPTODATE to track whether perf_aux_output_begin() and
perf_aux_output_end() are balanced. A cleared PERF_HES_UPTODATE bit
indicates that an AUX output context is still open.
Amend pt_event_start() / pt_event_stop() accordingly so that begin/end
stay balanced:
- In non-snapshot mode, stop() always closes the buffer (the buffer may
have run out of space, and that accounting is done by the update), so
a following start() opens a fresh one as before.
- In snapshot/overwrite mode, stop() without PERF_EF_UPDATE leaves the
buffer open so that pt_event_snapshot_aux() can still copy from it,
and start() then only re-enables tracing instead of calling
perf_aux_output_begin() again.
Note that pt_event_del() calls pt_event_stop() with PERF_EF_UPDATE flag set
(as is required by the documentation), so a final call to
perf_aux_output_end() is assured. |
| In the Linux kernel, the following vulnerability has been resolved:
pinctrl: bcm2835: Don't remove an unregistered GPIO chip
If the devm_pinctrl_register() function fails,
bcm2835_pinctrl_probe() calls gpiochip_remove()
before gpiochip_add_data() has registered the GPIO chip.
This means that upon failure the gpio_chip.gpiodev
is NULL resulting in a null pointer dereference
inside the gpiochip_remove() function.
Remove the unnecessary function call to gpiochip_remove().
No GPIO cleanup is required because the GPIO chip
has not yet been registered. Without this change there
is potential for a kernel panic upon registration failure |
| In the Linux kernel, the following vulnerability has been resolved:
regulator: tps6594: Fix device node reference leaks in multiphase loop
In tps6594_regulator_probe(), the multi-phase configuration loop calls
of_find_node_by_name() to find buck nodes by name, and of_get_parent()
twice to navigate to the PMIC parent node. None of the acquired node
references (np, intermediate parent, np_pmic_parent) are ever released
via of_node_put(), causing a reference leak on every loop iteration.
Additionally, of_find_node_by_name() can return NULL, but the result was
immediately passed to of_node_full_name() and of_get_parent() without a
NULL check, which could lead to a NULL pointer dereference.
Fix this by:
- Adding a NULL check for np after of_find_node_by_name()
- Storing the intermediate parent node in a local variable np_parent
- Calling of_node_put() on np, np_parent and np_pmic_parent at the
end of each loop iteration |
| In the Linux kernel, the following vulnerability has been resolved:
remoteproc: qcom_wcnss: Fix handling the lack of PD regulators in v3
The changes introduced to handle single power domain platforms have
swapped the info pointer increment from num_pd_vregs to num_pds, which
would shift the info pointer past the end of the array for pronto-v3,
which does not list power domain regulators in vregs.
This showed up as a difference between GCC- and LLVM-compiled kernels
on SDM632 devices, where only with LLVM one would get the
"regulator request with no identifier" error, because the out-of-bounds
memory ended up being zeroed. Fix by skipping the increment when there
are more power domains than regulators. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath11k: cap out-of-range rx MCS instead of leaving bogus rate
ath11k can receive HT/VHT/HE frames whose reported MCS is above the
maximum that can be expressed in the corresponding mac80211 rate space
(e.g. an HE frame reported with MCS 12, while HE tops out at MCS 11).
The frame itself is valid and decodes correctly, but for such a frame
ath11k_dp_rx_h_rate() leaves rx_status->rate_idx set to the out-of-range
value and never assigns rx_status->encoding, so it stays RX_ENC_LEGACY
from the ath11k_dp_rx_h_ppdu() initialization. Once that frame reaches
mac80211 it trips the rate sanity check and the frame is dropped with a
splat:
ath11k_pci 0000:03:00.0: Received with invalid mcs in HE mode 12
WARNING: CPU: 0 PID: 0 at net/mac80211/rx.c:5433 ieee80211_rx_list+0xb0a/0xe90 [mac80211]
Dropping the frame would discard otherwise valid data, so instead cap the
reported MCS to the maximum the rate space can express and deliver the
frame. Set rx_status->encoding before the range check and assign rate_idx
from the capped value, so a frame with an out-of-range MCS no longer
leaves partial or bogus rate metadata behind. Also downgrade the logging
level since they are not treated as invalid frames now. The only loss is
that such a frame is reported as the capped MCS in the rx rate statistics.
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.41 |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Disallow interpreter fallback for BPF_ADDR_PERCPU insn
The BPF_MOV64_PERCPU_REG insn requires JIT to emit native code to for
'dst_reg = src_reg + <percpu_base_off>'.
However, the interpreter ignores the 'off' at its ALU64_MOV_X label.
The 'off' indicates the insn is BPF_MOV64_PERCPU_REG insn. Then, when
the interpreter loads memory from the register, it will hit a page
fault.
[ 2.545572] BUG: unable to handle page fault for address: ffffffffacaaf034
[ 2.546485] #PF: supervisor read access in kernel mode
[ 2.547167] #PF: error_code(0x0000) - not-present page
[ 2.547850] PGD 134e63067 P4D 134e63067 PUD 134e64063 PMD 10021c063 PTE 800ffffeca550062
[ 2.548912] Oops: Oops: 0000 [#1] SMP PTI
Set jit_required as true in order to disallow interpreter fallback in
core.c::__bpf_prog_select_runtime(), if any BPF_ADDR_PERCPU insn is
patched to the prog.
BTW, rename the helper bpf_map_supports_cpu_flags() to
bpf_map_is_percpu_map(). |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: fix circular lock dependency in ext4_ext_migrate
Move iput(tmp_inode) after ext4_writepages_up_write() to avoid a
circular lock dependency between s_writepages_rwsem and sb_internal
(freeze protection).
The deadlock scenario:
CPU0 (EXT4_IOC_MIGRATE) CPU1 (orphan cleanup during mount)
---- ----
ext4_ext_migrate()
ext4_writepages_down_write()
s_writepages_rwsem (write)
ext4_evict_inode()
sb_start_intwrite() [sb_internal]
...
ext4_writepages()
s_writepages_rwsem (read) [BLOCKED]
iput(tmp_inode)
ext4_evict_inode()
sb_start_intwrite() [BLOCKED]
The tmp_inode is a temporary inode with nlink=0 created solely for
building the extent tree. Its eviction does not require
s_writepages_rwsem protection, so deferring iput() until after
releasing the rwsem is safe. |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: skip extra isize expansion during mount to prevent deadlock
ext4_try_to_expand_extra_isize() is called from __ext4_mark_inode_dirty()
while holding an active jbd2 handle. During mount (!SB_ACTIVE), the
expand path may move xattrs to external blocks and release ea_inodes via
iput(). When !SB_ACTIVE, iput() calls write_inode_now() which acquires
s_writepages_rwsem, creating a circular lock dependency:
s_writepages_rwsem --> jbd2_handle --> xattr_sem --> s_writepages_rwsem
This can be triggered via:
ext4_process_orphan() -> ext4_truncate() -> ext4_mark_inode_dirty()
-> ext4_try_to_expand_extra_isize()
or:
ext4_evict_inode() -> ext4_mark_inode_dirty()
-> ext4_try_to_expand_extra_isize()
Skip expansion when !SB_ACTIVE. This is a minor loss of functionality
(extra isize won't grow for these inodes during mount), which e2fsck
can resolve later if needed. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/core: Fix potential use after free in uverbs_free_dmah()
When accessing a dmah via the netlink path the only synchronization
mechanism for the said dmah is rdma_restrack_get().
Currently, rdma_restrack_del() is invoked at the end of
uverbs_free_dmah(), which is too late, since by that point
vendor-specific resources associated with the dmah might already be
freed. This can leave a short window where the dmah remains accessible
through restrack, leading to a potential use-after-free.
Fix this by moving the rdma_restrack_begin_del() call to the start of
uverbs_free_dmah(), ensuring that the dmah is removed from restrack
before its internal resources are released. This guarantees that no new
users hold references to a dmah that is in the process of destruction.
In addition, this change preserves the intended inverted order
between create and destroy routines: resources are added to
restrack at the end of successful creation, and hence shall be removed
from the restrack first thing during the destruction flow, which keeps
the lifecycle management consistent and predictable. |
| In the Linux kernel, the following vulnerability has been resolved:
arm64: RSI: fix field-spanning write warning in attestation token init
The challenge is passed in registers a1 through a8. However, copying to
®s.a1 makes FORTIFY treat the destination as the single a1 field,
resulting in a field-spanning write warning. [1]
Overlay the SMCCC register structure with an RSI-specific argument
layout and copy the challenge into an explicit 64-byte array. This keeps
the existing a1-a8 argument encoding while giving the copy a correctly
sized destination object.
[1]
memcpy: detected field-spanning write (size 64) of single field "®s.a1" at ./arch/arm64/include/asm/rsi_cmds.h:119 (size 8)
WARNING: ./arch/arm64/include/asm/rsi_cmds.h:119 at rsi_attestation_token_init+0xdc/0xf8 [arm_cca_guest], CPU#0: cat/3314 |
| In the Linux kernel, the following vulnerability has been resolved:
PCI/pwrctrl: tc9563: Fix parsing the integrated Ethernet MAC Endpoint node
DSP3 has an integrated Ethernet MAC Endpoint which has its own set of
config registers for configuring settings such as ASPM. The Endpoint device
has two physical functions and those two functions share the same settings.
Parse the Endpoint node under DSP3 instead of parsing both functions. The
existing parsing logic also has one OOB issue as parsing both functions
will result in accessing past the tc9563_pwrctrl->cfg array. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/efa: Fix PBL chunk length computation
On register MR, when creating the PBL, if it's an indirect PBL we create
a chunk list to hold the PBL pages pointers. Each chunk is 4KB in size
and can hold 510 addresses (EFA_PTRS_PER_CHUNK) and has a 12-byte
control buffer at the end of it holding the next chunk's pointer and its
length.
If the PBL number of pages is a multiple of EFA_PTRS_PER_CHUNK, the
calculated last chunk length is wrongly computed as 0, even though that
chunk is fully populated with 510 real page pointers. This wrong length
is used both to DMA map the chunk and is propagated to the device,
causing the device to see the chunk as empty and reject the memory
registration.
Fix the calculation so it will be performed only if the number of pages
isn't a multiple of EFA_PTRS_PER_CHUNK, if it is, its already handled in
the above loop correctly.
Also prevent out-of-bounds reach in the chunks array in such scenario. |
| In the Linux kernel, the following vulnerability has been resolved:
clk: eswin: Zero-initialize stack-allocated clk_init_data
eswin_clk_register_pll() and eswin_register_clkdiv() declare a struct
clk_init_data on the stack and only initialize some of its fields
(parent_data respectively parent_hws). clk_core_populate_parent_map()
checks parent_names first and parent_data second before falling back
to parent_hws, so leftover stack garbage in the uninitialized fields
hijacks parent resolution and the clk core dereferences a bogus
pointer:
Unable to handle kernel NULL pointer dereference at virtual address 000000000000000c
Oops [#1]
epc : __clk_register+0x31a/0x7f0
[<ffffffff805dc774>] __clk_register+0x31a/0x7f0
[<ffffffff805dcd76>] devm_clk_hw_register+0x2a/0x94
[<ffffffff805e319a>] eswin_register_clkdiv+0x80/0xd0
[<ffffffff805e34a0>] eswin_clk_register_clks+0x162/0x1a0
[<ffffffff805e3736>] eic7700_clk_probe+0x146/0x180
[<ffffffff8065d23c>] platform_probe+0x3c/0x7a
Observed on EIC7700 hardware (with the driver backported to a 6.17
tree); whether the bug triggers depends entirely on what the stack
happens to contain when the registration helpers run.
Zero-initialize both structures. |
| In the Linux kernel, the following vulnerability has been resolved:
md/raid5-ppl: fix use-after-free in ppl_do_flush()
The loop in ppl_do_flush() continues iterating after calling
ppl_io_unit_finished(), touching io->pending_flushes and leading to a
use-after-free.
Add a break statement to stop the loop once io is freed. |
| In the Linux kernel, the following vulnerability has been resolved:
locking/lockdep: Fix NULL pointer dereference in __lock_set_class()
register_lock_class() can return NULL when the lock class pool is
exhausted, graph_lock() fails, or key validation fails. However,
__lock_set_class() uses the return value directly in pointer arithmetic
without a NULL check:
class = register_lock_class(lock, subclass, 0);
hlock->class_idx = class - lock_classes;
If class is NULL, this computes a wild offset that corrupts
hlock->class_idx. The subsequent reacquire_held_locks() call will
invoke hlock_class() with this corrupted index, leading to a NULL or
out-of-bounds pointer dereference.
Add the missing NULL check, consistent with how __lock_acquire() already
handles this case at the same call site. |
| minimp3 commit ea99364f contains an integer overflow vulnerability in mp3dec_skip_id3v1() when parsing the APEv2 tag-size field. |
| In the Linux kernel, the following vulnerability has been resolved:
powerpc/xive: propagate IPI init errors to prevent use-after-free
When xive_init_ipis() fails (e.g. irq_domain_alloc_irqs() fails),
the error path frees the global xive_ipis array. However,
xive_smp_probe() previously ignored this failure and proceeded to
call xive_setup_cpu_ipi(), which dereferences the already-freed
xive_ipis pointer -- a use-after-free.
Now that xive_smp_probe() returns int (previous patch), propagate
the error from xive_init_ipis() and xive_setup_cpu_ipi() through
xive_smp_probe(). Check the return value in both pnv_smp_probe()
and pSeries_smp_probe() so that IPI setup is aborted cleanly on
failure, avoiding the use-after-free. |
