| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
nexthop: Initialize extack in remove_nh_grp_entry()
remove_nh_grp_entry() prints the extack message when a listener fails
to replace the reduced nexthop group. However, extack is not
initialized and listeners are not required to set a message when
returning an error. Neither netdevsim nor mlxsw do so when an
allocation fails, resulting in the dereference of an uninitialized
stack pointer.
Fix by zero-initializing extack, as was done in commit 6347c5314cee
("nexthop: initialize extack in nh_res_bucket_migrate()"). |
| In the Linux kernel, the following vulnerability has been resolved:
net: dsa: bcm_sf2: bound the CFP rule dump by the caller's buffer size
bcm_sf2_cfp_rule_get_all() walks the whole cfp.unique bitmap into
rule_locs[] without consulting nfc->rule_cnt, which is how many entries
the caller had room for. ETHTOOL_GRXCLSRLALL requires no CAP_NET_ADMIN
and the ioctl sizes the buffer from the rule_cnt userspace passes in, so
once an admin has installed CFP rules any user can ask for fewer slots
than there are rules and run off the end of the allocation. A rule_cnt
of 0 leaves the buffer pointer NULL and the walk dereferences it. |
| In the Linux kernel, the following vulnerability has been resolved:
eth: nfp: bound the ntuple rule dump by the caller's buffer size
nfp_net_get_fs_loc() dumps every entry of nn->fs.list into rule_locs[]
without consulting cmd->rule_cnt, which is how many entries the caller
had room for. ETHTOOL_GRXCLSRLALL requires no CAP_NET_ADMIN and the
ioctl sizes the buffer from the rule_cnt userspace passes in, so once an
admin has installed flow steering rules any user can ask for fewer slots
than there are rules and run off the end of the allocation. A rule_cnt
of 0 leaves the buffer pointer NULL and the walk dereferences it.
Bail out with -EMSGSIZE when the buffer fills up, the way the other
ntuple capable drivers do, and report how many locations were filled so
a shrinking rule list does not leave the caller reading stale slots. |
| In the Linux kernel, the following vulnerability has been resolved:
eth: nfp: drop the replaced rule from the list when reprogramming fails
nfp_net_fs_add() replaces an existing rule by deleting it from the
hardware, decrementing nn->fs.count and programming the new one. If
nfp_net_fs_add_hw() fails the old entry stays on nn->fs.list - only the
success path reaches list_replace() - so the list is one longer than
nn->fs.count, and it advertises a rule whose hardware entry has already
been torn down.
nn->fs.count is what ETHTOOL_GRXCLSRLCNT reports, so userspace then sizes
its buffer one entry short of what the GRXCLSRLALL walk wants to write.
That used to overwrite one u32 past the allocation; since the walk is
bounded it is a permanent -EMSGSIZE instead, as nothing ever resyncs the
counter. |
| In the Linux kernel, the following vulnerability has been resolved:
net: dsa: mv88e6xxx: bound the policy rule dump by the caller's buffer size
mv88e6xxx_get_rxnfc() uses rxnfc->rule_cnt as the write index while
dumping the policy IDR, clobbering the input value before it has been
looked at. That input is the number of entries the caller had room for.
ETHTOOL_GRXCLSRLALL requires no CAP_NET_ADMIN and the ioctl sizes the
buffer from the rule_cnt userspace passes in, so once an admin has
installed policy rules any user can ask for fewer slots than there are
rules and run off the end of the allocation. A rule_cnt of 0 leaves the
buffer pointer NULL and the walk dereferences it.
Count into a local so the caller's limit survives the walk, and stop with
-EMSGSIZE once it is reached. |
| In the Linux kernel, the following vulnerability has been resolved:
net: bridge: mcast: properly convert mglist to rcu
Sashiko reported a bug [1] that br_multicast_del_port_group unlists the
port group not using proper rcu helper that preserves the next pointer and
after that immediately frees the port group without waiting for rcu grace
period. The only rcu walker of mglist is br_multicast_list_adjacent() and
it turns out that function has always been buggy because mglist was never
properly converted to RCU. Fix it by converting it to rcu and moving its
initialization after eth_addr's. Initializing p->next can use
RCU_INIT_POINTER because we have a barrier from the hlist_add_head_rcu call
later, besides we're initializing an unpublished structure anyway.
[1] https://netdev-ai.bots.linux.dev/sashiko/#/patchset/20260826014200.362304-1-littleddfu%40gmail.com |
| In the Linux kernel, the following vulnerability has been resolved:
net: usb: cx82310_eth: drop URB after 0xffff reboot sentinel to prevent partial_data heap overflow
The 0xffff length sentinel detects a router reboot and schedules
re-enabling of ethernet mode, but then falls through to the rest
of the loop body. The next check is
} else if (len > CX82310_MTU) {
which is the else of the just-matched if -- it never fires for
len == 0xffff. The MTU bound that normally caps the
incomplete-packet save path is silently bypassed.
With 0xffff > skb->len always true (rx_urb_size is 4096), the
incomplete-packet branch saves dev->partial_len = skb->len bytes
into dev->partial_data. partial_data is kmalloc(hard_mtu) =
kmalloc(CX82310_MTU + 2) = 1516 bytes, but skb->len after the
2-byte header pull can be up to 4094. A device that sends a
4096-byte URB starting with [0xff 0xff] therefore copies 4094
device-provided bytes into a buffer allocated for 1516 bytes,
exceeding its requested size by 2578 bytes.
The next URB then reads dev->partial_len (4094) back from the same
1516-byte buffer and dev->partial_rem (65535 - 4094 = 61441) from
the new URB's ~4KB skb, both well past their allocations, and
delivers the spliced result as a 64KB "frame" to the network
stack.
Bail out of rx_fixup after scheduling the re-enable work; the
remainder of a reboot-marker URB is not meaningful packet data.
This restores the invariant that partial_len < CX82310_MTU + 2 on
the save path, since every other route there has already passed
the MTU check. |
| In the Linux kernel, the following vulnerability has been resolved:
s390/ism: folio_put() after error
dmb->cpu_addr was allocated via folio_alloc(). Use folio_put() instead of
kfree() in the error exit of ism_alloc_dmb() to avoid slab allocator
corruption.
While at it, reset dmb->cpu_addr after folio_put to avoid unintentional UAF
by future callers. |
| In the Linux kernel, the following vulnerability has been resolved:
vxlan: reject dynamic fdb entries that reference a nexthop id
The commit cited in the Fixes tag allowed VXLAN FDB entries to point to
FDB nexthops so that overlay traffic could be load balanced across
multiple VTEPs. Such entries can only be configured from user space,
cannot be learned and cannot roam. They only make sense with a user space
control plane such as E-VPN where data plane learning is disabled.
Despite that, the VXLAN driver does not currently prevent such entries
from being configured with the "dynamic" flag. The per-nexthop FDB list
is only protected by the per-device hash lock, which is not sufficient
when two VXLAN devices point to the same FDB nexthop and therefore share
the list. Aging runs in softirq context without RTNL, so an entry deleted
by one device can race with an addition or deletion from the other,
leading to list corruption:
list_del corruption. next->prev should be ffff8881069d9548, but was
dead000000000122. (next=ffff8881069d9448)
WARNING: CPU: 0 PID: 90 at lib/list_debug.c:65
__list_del_entry_valid_or_report+0x1aa/0x210
...
vxlan_fdb_destroy+0x5b8/0xad0
vxlan_cleanup+0x328/0x450
call_timer_fn+0x2a/0x1c0
run_timer_softirq+0x18c/0x210
BUG: KASAN: slab-use-after-free in vxlan_fdb_destroy
Fix this by rejecting the bogus configuration of dynamic FDB entries that
point to FDB nexthops, both when created and when an existing entry is
updated. As such, the per-nexthop FDB list is only ever mutated under the
RTNL lock. Add test cases to make sure that this does not regress in the
future. |
| In the Linux kernel, the following vulnerability has been resolved:
net: cap tx_queue_len at S16_MAX to prevent oversized ring allocations
Several subsystems allocate ring buffers sized by dev->tx_queue_len
with no upper bound. An unprivileged user (via unshare -Urn) can set a
huge tx_queue_len and exhaust global memory with ring allocations:
- pfifo_fast: pfifo_fast_init() and pfifo_fast_change_tx_queue_len()
allocate 3 skb_array rings of tx_queue_len entries each.
- tun: tun_queue_resize() and the queue-attach path resize ptr_rings
to tx_queue_len on the NETDEV_CHANGE_TX_QUEUE_LEN notifier.
- tap (macvtap/ipvtap): tap_queue_resize() and tap_init() resize/init
ptr_rings to tx_queue_len on the same notifier.
netif_change_tx_queue_len() is the single entry point for IFLA_TXQLEN,
sysfs, and the SIOCSIFTXQLEN ioctl. Cap new_len at S16_MAX (32767)
there so the oversized value is rejected at set time. This takes
effect whether the device is up or down, before dev->tx_queue_len is
written, before any notifier fires, and before any ring is allocated.
The "> S16_MAX" check also subsumes the previous unsigned-long
truncation test, and a negative ifr_qlen from the ioctl lands far
above the cap after conversion, so both old failure modes are covered
by the one comparison.
tx_queue_len is ambigious: both a per-ring sizing multiplier and a
default queue-length/limit knob for consumers that allocate
nothing at set time (pfifo/bfifo/gred/plug/sfb limits, htb
direct_qlen, qfq max_classes, teql). 32767 is chosen as the largest
value NLA_POLICY_FULL_RANGE can express for the u32 IFLA_TXQLEN
policy in patch 2/3 while staying a legitimate queue length on
high-BDP paths; the ring-memory trade-off of a shared knob is
disclosed below.
Conditions to recreate the bug:
- CONFIG_NET_SCHED=y, CONFIG_VETH=y, CONFIG_USER_NS=y, CONFIG_NET_NS=y.
- Unprivileged user in a fresh user+net namespace (unshare -Urn).
- pfifo_fast: create veth pairs, set tx_queue_len to 500000, attach
mq+pfifo_fast. ~28 iterations OOMs a 2GB guest.
- tun: create 50 tun devices with IFF_MULTI_QUEUE, set tx_queue_len to
500000, open 8 queues each. ~1.6GB of ptr_ring allocations OOMs a
512MB guest.
- tap: same as tun with IFF_TAP. ~960MB OOMs a 512MB guest.
- On the fixed kernel the oversized tx_queue_len is rejected with
-ERANGE at set time (all four paths: RTM_SETLINK, RTM_NEWLINK
create, sysfs, ioctl - the latter two via this check, the former
two via this check and the 2/3 parse policy respectively). |
| In the Linux kernel, the following vulnerability has been resolved:
net: reject oversized tx_queue_len at netlink parse time
rtnl_create_link() assigns IFLA_TXQLEN directly to dev->tx_queue_len
without going through netif_change_tx_queue_len(), so a device created
with "ip link add ... txqueuelen 500000" bypasses the S16_MAX cap and
still triggers the oversized ring allocations in pfifo_fast, tun and
tap. The veth peer nest (rtnl_nla_parse_ifinfomsg()) and the
RTM_NEWLINK-on-existing-device path reach the same sinks.
Enforce the cap in ifla_policy instead: IFLA_TXQLEN becomes
NLA_POLICY_FULL_RANGE(NLA_U32, &txqlen_range) with
txqlen_range = { .min = 0, .max = S16_MAX }. All netlink consumers
parse against this policy - rtnl_setlink(), rtnl_newlink() (create
and change), and the veth peer nest - so every netlink path is capped
at parse time and rejects the attribute with -ERANGE plus a proper
"integer out of range" extack message before any device state is
modified (the RTM_SETLINK half-application wart is gone with it).
Document the bound in the rt-link.yaml netlink spec.
Conditions to recreate the bug:
- CONFIG_NET_SCHED=y, CONFIG_VETH=y, CONFIG_USER_NS=y, CONFIG_NET_NS=y.
- Unprivileged user in a fresh user+net namespace (unshare -Urn):
ip link add v0 txqueuelen 500000 type veth peer name v1
-> on the fixed kernel this is rejected with -ERANGE ("integer out
of range" extack) instead of installing an oversized tx_queue_len
that later inflates pfifo_fast/tun/tap ring allocations.
- ip link set v0 txqueuelen 500000 is likewise rejected at parse time. |
| In the Linux kernel, the following vulnerability has been resolved:
pds_core: fix cmd_regs access racing BAR unmap on reset
pdsc_reset_prepare() and pdsc_reset_done()'s pdsc_map_bars() error path
clear/iounmap cmd_regs without devcmd_lock, and
pdsc_legacy_firmware_update()'s download loop derefs cmd_regs after
dropping and retaking the lock without re-checking. An FLR concurrent
with a devlink flash can unmap cmd_regs under an in-flight devcmd,
causing a NULL deref or a write to unmapped MMIO.
Take devcmd_lock across the BAR unmap/remap, and re-check cmd_regs in
the download loop. Only the PF maps cmd_regs and runs devcmd, so skip
the unmap on a VF, as pdsc_remove() and pdsc_reset_done() already do.
A reset that completes entirely within the unlocked window is not a
correctness problem for the image: the device clears its update session,
so a resumed download is rejected, and it verifies the staged image
before writing a flash slot, reporting PDS_RC_BAD_FW rather than
activating it.
pdsc_unmap_bars() also clears info_regs, intr_status and intr_ctrl. The
interrupt and start/stop readers of those are quiesced before the unmap
by pdsc_fw_down(), which frees the interrupts and tears down the queues.
The debugfs readers are not, since those files outlive a reset; that is
pre-existing and out of scope here. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: mark a NULL call argument precise
check_func_arg() allows bpf_register_is_null() for nullable arguments
w/o marking the underlying scalar register precise. Hence a checkpoint
created on such a path would prune against arbitrary scalar value.
check_helper_call() enforces second parameter of the
bpf_get_local_storage() to be zero, w/o marking the underlying scalar
register precise. Hence a checkpoint created on such a path would
prune against arbitrary scalar value.
Grouping these two into one patch, as they share the same fixes tag. |
| In the Linux kernel, the following vulnerability has been resolved:
net: mctp: i3c: serialize probe with bus removal
mctp_i3c_probe() drops busdevs_lock after finding the matching bus. A
concurrent I3C_NOTIFY_BUS_REMOVE can then unregister and free the bus
netdev before probe passes its private data to mctp_i3c_add_device().
The latter consequently adds a list node through a freed mbus pointer.
Keep busdevs_lock held until the device has been added. This also
satisfies the __must_hold annotation on mctp_i3c_add_device(). |
| In the Linux kernel, the following vulnerability has been resolved:
net/sched: defer qdisc freeing after failed creation
An RTM_NEWQDISC request can make clsact bind a populated shared ingress
block during ->init(), publishing an embedded mini_Qdisc to lockless
readers. If the same request has an invalid TCA_RATE, estimator setup
fails after ->init(); the unwind removes the pointer but synchronously
frees its containing qdisc while tc_run() may still hold it.
Retire failed qdiscs through the same RCU helper as normal destruction.
Inline the synchronous free into the callback now that no direct callers
remain. |
| In the Linux kernel, the following vulnerability has been resolved:
net/mlx5e: Fix use-after-free race in sample_restore_put()
Concurrent teardown of TC sample rules sharing the same restore
context may re-read restore->count after dropping restore_lock.
At that point another thread may already have completed cleanup and
freed the restore object.
Use the result of the refcount decrement while holding restore_lock to
determine whether cleanup is needed. |
| In the Linux kernel, the following vulnerability has been resolved:
net/mlx5: E-Switch: fix use-after-free in mlx5_eswitch_termtbl_put
In mlx5_eswitch_termtbl_put(), the zero-ref cleanup check reads
tt->ref_count after termtbl_mutex has been released. Two concurrent
callers on the same mlx5_termtbl_handle race: one decrements ref_count
to zero, removes the hash entry, and calls kfree(tt) while the other
has already dropped the mutex and is about to evaluate
if (!tt->ref_count), producing a use-after-free.
Fix this by capturing the result of the decrement into a stack-local
last variable before dropping the mutex. The cleanup decision is now
made entirely under termtbl_mutex, and tt is not touched after
kfree. |
| In the Linux kernel, the following vulnerability has been resolved:
net/mlx5: E-Switch, prevent mc_list repopulation during vport disable
In mlx5_esw_vport_disable(), move esw_apply_vport_rx_mode() ahead
of esw_vport_change_handle_locked() so vport->allmulti_rule is
NULL before the change handler observes it.
During FW-fatal recovery the disable runs while dev->state ==
INTERNAL_ERROR. The promisc query inside esw_update_vport_rx_mode()
fails and returns early, leaving vport->allmulti_rule intact, so
esw_update_vport_mc_promisc() runs and adds MLX5_ACTION_ADD entries
to vport->mc_list whose flow rules are then installed in the FDB
by esw_add_mc_addr(). esw_destroy_legacy_table() tears down the
FDB with those refs still held, corrupting the sub-tree and
leaving dangling flow_rule pointers in vport->mc_list.
Two-stage failure on `echo 1 > /sys/bus/pci/devices/<bdf>/reset`:
refcount_t: underflow; use-after-free.
tree_put_node+0xef/0x110 [mlx5_core]
clean_tree+0x44/0xd0 [mlx5_core] (x5)
mlx5_fs_core_cleanup+0x57/0x1c0 [mlx5_core]
mlx5_unload+0x65/0xd0 [mlx5_core]
... mlx5_health_try_recover
BUG: unable to handle page fault for address: 0000000003000055
down_write+0x1c/0x60
mlx5_del_flow_rules+0x33/0x1f0 [mlx5_core]
esw_del_mc_addr+0x7b/0x170 [mlx5_core]
esw_apply_vport_addr_list+0x56/0xf0 [mlx5_core]
esw_vport_change_handle_locked+0x28b/0x310 [mlx5_core]
mlx5_esw_vport_enable+0x270/0x4a0 [mlx5_core]
... mlx5_load ... mlx5_health_try_recover
esw_apply_vport_rx_mode(false, false) clears vport->allmulti_rule
via its local state machine even when the FW del fails. With the
rule NULL the !IS_ERR_OR_NULL(allmulti_rule) gate in the change
handler closes, no rules are installed during disable, and the
reload starts with a clean mc_list. |
| In the Linux kernel, the following vulnerability has been resolved:
net/sched: fq_pie: clamp quantum in change path
fq_pie_change() accepts any quantum value from userspace, including 1.
With a crafted size table qdisc_pkt_len reaches ~2 GiB, so quantum=1
makes the deficit-refill loop spin ~2^31 times under the qdisc lock
(a soft lockup / denial of service).
Add max(256U, ...) matching fq_codel_change().
Conditions to recreate the bug:
CONFIG_NET_SCH_FQ_PIE=y. Requires CAP_NET_ADMIN (namespace-local via
unshare -Urn suffices).
tc qdisc add dev dummy0 root fq_pie
tc qdisc change dev dummy0 root fq_pie quantum 1 stab data 32768 size_log 15 cell_log 0 |
| In the Linux kernel, the following vulnerability has been resolved:
net/sched: sfq: clamp quantum in change path
sfq_change() accepts any non-negative quantum (only rejects
(int)ctl->quantum < 0). With a crafted size table qdisc_pkt_len reaches
~2 GiB, so quantum=1 makes the deficit-refill loop spin ~2^31 times
under the qdisc lock (a soft lockup / denial of service).
Add max(256U, ...) matching fq_codel_change(). Reject quantum > 1<<20
with -EINVAL, matching fq_codel_change() and the init clamp.
Conditions to recreate the bug:
CONFIG_NET_SCH_SFQ=y. Requires CAP_NET_ADMIN (namespace-local via
unshare -Urn suffices).
tc qdisc add dev dummy0 root sfq
tc qdisc change dev dummy0 root sfq quantum 1 stab data 32768 size_log 15 cell_log 0 |
