| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
firmware: arm_scmi: Fix SCMI device destroy lifetimes
scmi_child_dev_find() drops the reference returned by
device_find_child() before returning the scmi_device pointer. A
concurrent unregister can then release the device while the destroy path
is still using the returned pointer.
Make the lookup helper return the device_find_child() reference and keep
it until scmi_device_destroy() has finished unregistering the child.
Also split device_unregister() in __scmi_device_destroy() so the SCMI bus
ID is not made reusable until after device_del() has removed the old
scmi_dev.N name from sysfs. This avoids a new SCMI device reusing the
same ID while the old device is still registered.
The final device release callback is also a possible cleanup path when
SCMI children are deleted by driver core recursion rather than
__scmi_device_destroy(). Release the SCMI bus ID from a common helper
used by destroy, register-failure and final-release paths, and clear
scmi_dev->id after freeing it so the final release cannot free the same
ID again. |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: clear stale xarray tags on folios skipped during writeback
In data=journal mode, the writeback thread can hit the
WARN_ON_ONCE(sb_rdonly(sb)) in ext4_journal_check_start() while the
superblock is being remounted read-only during reboot:
Workqueue: writeback wb_workfn (flush-253:0)
RIP: 0010:ext4_journal_check_start+0x8b/0xd0
Call Trace:
__ext4_journal_start_sb+0x3c/0x1e0
mpage_prepare_extent_to_map+0x4af/0x580
ext4_do_writepages+0x3c0/0x1080
ext4_writepages+0xc8/0x1a0
do_writepages+0xc4/0x180
__writeback_single_inode+0x45/0x2f0
writeback_sb_inodes+0x26b/0x5d0
__writeback_inodes_wb+0x54/0x100
wb_writeback+0x1ac/0x320
wb_workfn+0x394/0x470
And followed by the warning:
EXT4-fs warning (device vda1): ext4_evict_inode:195: inode #6263:
comm (sd-umount): data will be lost
This issue is not reproduced every time, but frequently.
The reproduction step is to create a VM with 8 CPUs, 16G memory and
setup data=journal:
sudo tune2fs -o journal_data /dev/vda1
Run fio:
rm -f fiotest
fio --name=fiotest --rw=randwrite --bs=4k --runtime=6 --ioengine=libaio
--iodepth=256 --numjobs=8 --filename=fiotest --filesize=30G
--group_reporting
Reboot the VM, and check the console output from:
virsh console testvm
But there is no dirty inode, folio_clear_dirty_for_io clears PG_dirty
but leaves tags PAGECACHE_TAG_DIRTY and PAGECACHE_TAG_TOWRITE set which
are only cleared by __folio_start_writeback.
In data=journal mode, jbd2 checkpoints the journalled data to its final
location and clears its own dirty flag without touching folio PG_dirty
or xarray dirty flags.
The commit f4a2b42e7891 ("ext4: fix stale xarray tags after writeback")
fixes when PG_dirty is still set but there is no dirty page.
Another case is PG_dirty is cleared, but PAGECACHE_TAG_DIRTY and
PAGECACHE_TAG_TOWRITE is still set. In this case, writeback thread
checks clean folio and skips it in mpage_prepare_extent_to_map:
if (!folio_test_dirty(folio) ||
...
folio_unlcok(folio);
continue
And never reaches ext4_bio_write_folio where the commit f4a2b42e7891
clears the stale xarray tags. Print debug logs after the filesystem
is remounted read-only:
writepages RDONLY nrpages=2048 dirtytag=1 wbtag=0 towrite=1 sync=0
And all folios are actually clean:
folio idx=3 dirty=0 wb=0 checked=0 dirtybuf=0 jbddirty=0 mapped=1
...
We need to clear the xarray stale tags for such clean folios by
cycling them through writeback in the skip path, the same way
f4a2b42e7891 does in ext4_bio_write_folio. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Preserve unique-field state across nested structs
btf_find_struct_field() initializes a fresh seen mask for every recursive
descent. Unique special fields in different levels of the same aggregate
therefore do not see one another. The duplicate fields can reach
btf_parse_fields(), where they trigger an invariant WARN_ON_ONCE(). A
crafted user BTF can consequently trigger the warning before map creation
checks capabilities.
Initialize the seen mask once in btf_find_field() and pass the same pointer
through struct, datasec, and nested-struct walks. This gives the entire field
traversal one shared uniqueness state. |
| In the Linux kernel, the following vulnerability has been resolved:
iommu/tegra241-cmdqv: Don't run the error ISR before probe sets up vintfs
__tegra241_cmdqv_probe() requests the error IRQ before it has allocated the
cmdqv->vintfs array and set cmdqv->num_vintfs. A CMDQV left enabled with a
latched error across a kexec fires the IRQ as soon as it is requested, and
tegra241_cmdqv_isr() then walks the uninitialized cmdqv->vintfs array.
Request the IRQ only after cmdqv->vintfs is allocated and zeroed, so that
a latched interrupt firing early runs the ISR against a valid array of NULL
slots that it safely skips. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7996: clear stale link state on full reset
After a full chip reset, mac80211 reconfig replays interface, link and
channel context setup. mt7996_vif_link_add() short-circuits when the
link_id is still marked in mvif->valid_links, a state introduced for
postponing link teardown to interface removal. The reset path frees the
link structures without clearing those bits, so the replayed setup never
re-creates dev_info/bss_info/STA records in the restarted firmware and
never re-registers the link wcid, leaving the device inoperative.
The reset path also leaks every allocated MLD index: per-link indices
and the per-vif group/remap indices are re-allocated from scratch during
reconfig, but the old bits stay set in the masks, so repeated full
resets exhaust the index space.
Clear valid_links in the reset vif iterator and reset the MLD index
masks alongside the existing omac_mask clearing. |
| In the Linux kernel, the following vulnerability has been resolved:
phy: qcom: qmp-usb-legacy: Fix possible NULL-deref on early runtime suspend
There is a small window where the runtime suspend callback may run
after pm_runtime_enable() and before pm_runtime_forbid(). In this
case, a crash occurs because runtime suspend/resume dereferences
qmp->phy pointer, which is not yet initialized:
`if (!qmp->phy->init_count) {`
This can also happen if user re-enables runtime-pm via the sysfs
attribute before qmp phy is initialized.
Similarly to other qcom phy drivers, introduce a qmp->phy_initialized
variable that can be used to avoid relying on the possibly uninitialized
phy pointer. |
| In the Linux kernel, the following vulnerability has been resolved:
ARM: 9484/1: enable interrupts when unhandled user faults are triggered
PREEMPT_RT requires interrupts to be enabled when sending signals.
When do_DataAbort()/do_PrefetchAbort() triggers unhandled user faults,
that is `inf->fn()` return a non-zero value, and the interrupts are not
enabled within the hook function, force_sig_fault() will be called
with interrupts disabled.
This can be triggered by user programs executing the bkpt instruction,
with kernel config CONFIG_PERF_EVENTS=n.
Enable interrupts in do_DataAbort()/do_PrefetchAbort() when unhandled
user faults are triggered to fix the issue. |
| In the Linux kernel, the following vulnerability has been resolved:
thermal: hwmon: Remove hwmon class device along with its parent
The current code creates one hwmon device per thermal zone type and that
device is registered under the first thermal zone of the given type.
That turns out to be problematic when the thermal zone holding the
hwmon device is removed.
For example, say that there are two ACPI thermal zones on a system
/sys/devices/virtual/thermal/thermal_zone0/
/sys/devices/virtual/thermal/thermal_zone1/
The current code registers a hwmon class device for thermal_zone0 only:
/sys/devices/virtual/thermal/thermal_zone0/hwmon0/
because the type is "acpitz" for both of them, but it adds a sysfs
attribute that belongs to thermal_zone1 under it:
/sys/devices/virtual/thermal/thermal_zone0/hwmon0/temp2_input
There is also
/sys/devices/virtual/thermal/thermal_zone0/hwmon0/temp1_input
which belongs to thermal_zone0.
When thermal_zone0 is removed, say because the ACPI thermal driver is
unbound from the underlying platform device, thermal_remove_hwmon_sysfs()
skips the removal of hwmon0 because of the temp2_input attribute
belonging to thermal_zone1 which effectively prevents thermal_zone0
removal from making progress.
Address this by making thermal_remove_hwmon_sysfs() remove the entire
hwmon class device interface for the given thermal zone type when the
thermal zone device holding it is removed.
To prevent races with thermal_add_hwmon_sysfs() that may interfere
with this, carry out the entire addition and removal of hwmon sysfs
interfaces for thermal zones under thermal_hwmon_list_lock.
Also adjust the layout of the labels in thermal_add_hwmon_sysfs() to
the current kernel coding style to align with the new "unlock" label. |
| In the Linux kernel, the following vulnerability has been resolved:
arm64/efi: Avoid voluntary preemption with efi_mm installed
Gus reports a bad kernel memory access when using software PAN
(CONFIG_ARM64_SW_TTBR0_PAN=y) on a machine with support for EFI runtime
services:
Unable to handle kernel access to user memory outside uaccess routines
at virtual address 00000000f322ff30
Mem abort info:
ESR = 0x0000000096000004
FSC = 0x04: level 0 translation fault
Internal error: Oops: 0000000096000004 [#1] SMP
Workqueue: efi_rts_wq efi_call_rts
pstate: 80400005 (Nzcv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : efi_call_rts+0xd8/0x288
Call trace:
efi_call_rts+0xd8/0x288 (P)
process_one_work+0x178/0x4f8
worker_thread+0x194/0x328
This is because the fpsimd context management code called from
__efi_fpsimd_begin() can preempt voluntarily, returning later to the EFI
code with an incorrect value for TTBR0_EL1 thanks to the deferred mm
switching used by the software PAN implementation.
Since EFI runtime services cannot preempt voluntarily and because the
fpsimd switching code does not rely on the TTBR0_EL1 mappings, simply
reorder the fpsimd switch so that it occurs before we change the
page-table. |
| In the Linux kernel, the following vulnerability has been resolved:
fuse: invalidate the correct range after O_APPEND direct write
fuse_direct_write_iter() captures pos before generic_write_checks(),
which moves ki_pos to EOF for O_APPEND writes:
fuse_direct_write_iter()
{
pos = iocb->ki_pos; /* 0 (user-supplied) */
generic_write_checks(); /* ki_pos -> EOF */
fuse_direct_io(); /* writes at EOF, correct */
invalidate(pos, pos + res); /* [0, res) -- wrong */
}
The post-write invalidation targets a stale range instead of the
actual written range at EOF.
This can cause data inconsistency when the file size is not
page-aligned. The tail page straddling EOF has a valid portion
before EOF that concurrent readers can fault back in during the
DIO write window:
Tail page (file size X not page-aligned):
page_start X (EOF) page_end
|--- valid data ----|-- stale --|
CPU0 (O_APPEND DIO writer) CPU1 (buffered reader)
-------------------------- ----------------------
invalidate [X, X+len)
tail page evicted
FUSE_WRITE in flight ...
read [page_start, X)
tail page re-faulted
[X, page_end) = stale
FUSE_WRITE completes
i_size = X + len
invalidate [0, len) <- WRONG
tail page still cached
read [X, X+len)
hits stale tail page
returns old data
Fix by reading pos back from iocb->ki_pos after generic_write_checks(),
as generic_file_direct_write() does.
Also fix a typo in the comment ("may have" -> "may have competed"). |
| In the Linux kernel, the following vulnerability has been resolved:
vsock: don't check the listener's sk_err in vsock_accept()
Syzbot reported an issue which can be reproduced with these steps:
r0 = socket(AF_VSOCK, SOCK_STREAM, 0)
bind(r0, {VMADDR_CID_ANY, PORT})
connect(r0, {VMADDR_CID_LOCAL, PORT}) -> -1, EPROTO (self-connect)
listen(r0, backlog) -> 0
r1 = socket(AF_VSOCK, SOCK_STREAM, 0)
connect(r1, {VMADDR_CID_LOCAL, PORT}) -> 0
accept(r0) -> -1, EPROTO (stale sk_err)
Basically, it creates a socket (r0) and triggers a self-connect after
binding it. This self-connect fails with EPROTO because it loops back
to r0 while the socket is still in the TCP_SYN_SENT state, causing it
to be incorrectly dispatched to the connecting-client path. The
unexpected packet type encountered there sets sk_err to EPROTO.
After that, it invokes a listen() call on the same socket. This
listen() call succeeds because the kernel's listening path never
inspects or clears sk_err. Then, a new socket (r1) is created as a
normal client and connects to r0. However, vsock_accept() rejects this
incoming connection because the listener's sk_err still holds the
EPROTO error from the earlier failed self-connect.
This rejection causes the child socket created for r1's connection to
never be freed on virtio or hyperv transports; only the VMCI transport
implements pending_work to revisit and clean up a rejected socket.
For a non-blocking connect(), vsock_connect() may return -EINPROGRESS
immediately, and vsock_connect_timeout() can later set sk->sk_err
asynchronously.
Since no vsock transport ever sets sk_err on a socket while it is in
TCP_LISTEN state, checking it in vsock_accept() serves no purpose and
only carries forward errors left behind by earlier, unrelated
connection attempts on the same socket. Remove the checks so accept()
no longer rejects valid incoming connections because of a stale
error, which also avoids the resource leak described above. |
| A memory initialization issue was addressed with improved memory handling. This issue is fixed in iOS 26.7 and iPadOS 26.7, iOS 27 and iPadOS 27, macOS Golden Gate 27, macOS Sequoia 15.8, macOS Tahoe 26.7, tvOS 27, visionOS 27, watchOS 27. An app with root privileges may be able to read uninitialized kernel memory. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: Fix init ordering in amdgpu_vram_mgr_init()
drmm_cgroup_register_region() is called before INIT_LIST_HEAD() and
gpu_buddy_init() in amdgpu_vram_mgr_init(). If it fails, the function
returns early and bypasses those initializations.
Since adev->mman.initialized is set to true before amdgpu_vram_mgr_init()
is called, a failure triggers amdgpu_ttm_fini(), which calls
amdgpu_vram_mgr_fini(), which then:
- Calls list_for_each_entry_safe() on reservations_pending and
reserved_pages, whose list_head::next pointers are zero-initialized
(NULL). The loop does not recognize them as empty and dereferences NULL.
- Calls gpu_buddy_fini(), which iterates free_trees[] unconditionally
via for_each_free_tree(). Since mm->free_trees is NULL
(never allocated), this dereferences NULL.
Both result in a kernel panic on the module load error path.
Fix by moving drmm_cgroup_register_region() to after the list and buddy
allocator are fully initialized, so the teardown path is safe to run. |
| In the Linux kernel, the following vulnerability has been resolved:
f2fs: fix to pass folio->index to f2fs_sanity_check_node_footer()
Otherwise in f2fs_sanity_check_node_footer(), it will check the
same nid incorrectly. |
| In the Linux kernel, the following vulnerability has been resolved:
f2fs: fix to clear dirty flag on folio in error path
If node block is corrupted due to chksum mismatch or inconsistent
footer info, it needs to drop clear flag of node folio, in order
to persist inconsistent node data to storage. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: qla2xxx: Skip NVMe LS reject IOCB when FW not started
qla_nvme_xmt_ls_rsp() bails out to the out: label when firmware is not
started (!ha->flags.fw_started), but the out: path unconditionally calls
qla_nvme_ls_reject_iocb(), which ends in qla2x00_start_iocbs() and an
unconditional doorbell write to the request queue in-pointer register.
This rings the firmware doorbell and queues an IOCB that stopped or
resetting firmware cannot consume, and touches MMIO during the reset/EEH
window where fw_started is also clear.
Only emit the LS reject IOCB (and ring the doorbell) when fw_started is
set; otherwise just clean up and return. The post-allocation failure
cases (SRB alloc / qla2x00_start_sp() failure) run with firmware started
and still send the reject. Apply the same guard to the reject emission
in qla2xxx_process_purls_pkt(). |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: arm64: Remove VM-wide VNCR mapping counter
The global VNCR mapping counter is used to decide whether an L1
provided VNCR page is mapped in L0 on any CPU at the point of
dealing with a TLB invalidation. It is incremented when a mapping
is made in the fixmap, and decremented when unmapped.
As it turns out, this tracking has several flaws:
- we are trying to invalidate TLBs, and the mapping is only an
opportunistic consequence of the TLB. Checking this counter to
decide whether a TLB needs to be invalidated may result in missed
invalidations.
- an L1 vcpu invalidating its own TLB (a very likely case) will not
succeed in invalidating the VNCR pseudo TLB because that page is
not mapped in L0 at this stage.
Given that this tracking fails at delivering the minimum guarantees
that are required and is only a performance optimisation, remove it
completely. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: qla2xxx: Initialize NVMe abort_work once at submission
qla_nvme_fcp_abort() and qla_nvme_ls_abort() ran INIT_WORK() on
priv->abort_work immediately before schedule_work(). INIT_WORK()
reinitializes the work_struct, resetting its list head and clearing the
pending bit. If an abort is issued more than once for the same command
(for example, concurrent transport teardown and a timeout-driven abort),
the second INIT_WORK() reinitializes a work item that is already queued,
which can corrupt the workqueue list and lead to crashes or a looping
worker.
Initialize priv->abort_work once at command submission, next to the
existing per-command spin_lock_init(&priv->cmd_lock), and leave only
schedule_work() in the abort paths. schedule_work() already does nothing
when the work item is still pending, so a repeated abort no longer
disturbs an in-flight work item. The command is not returned to the
transport until the final kref_put()/release callback runs after
abort_work has completed, so the work item is idle before priv is reused
and the single submission-time INIT_WORK() is safe. |
| In the Linux kernel, the following vulnerability has been resolved:
media: chips-media: wave5: Resume device before setting EOS flag
Setting the EOS flag talks to the firmware via send_firmware_command(),
which accesses VPU registers. Both the STREAMOFF path
(wave5_vpu_dec_job_abort()) and the V4L2_DEC_CMD_STOP path
(wave5_vpu_dec_stop()) can run while the device is runtime suspended, so
those register accesses hit powered-down hardware and the SoC raises an
asynchronous SError, panicking the kernel:
SError Interrupt on CPU3, code 0x00000000bf000000 -- SError
send_firmware_command+0x2c/0x160 [wave5]
wave5_vpu_dec_set_bitstream_flag+0x6c/0x80 [wave5]
wave5_vpu_dec_update_bitstream_buffer+0x80/0xec [wave5]
wave5_vpu_dec_job_abort+0x44/0xa0 [wave5]
v4l2_m2m_cancel_job+0x110/0x19c [v4l2_mem2mem]
v4l2_m2m_streamoff+0x24/0x140 [v4l2_mem2mem]
Resume the device with pm_runtime_resume_and_get() around the EOS
firmware command and release it with pm_runtime_put_autosuspend(),
matching the runtime PM handling already done in
wave5_vpu_dec_device_run(). |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: harmony: initialize locks before requesting IRQ
snd_harmony_create() registers the IRQ before initializing h->lock and
h->mixer_lock. A pending interrupt can invoke the handler while these
locks are uninitialized.
Initialize both locks before requesting the IRQ so the handler always
sees valid lock state. |
