| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: brcmfmac: fix crash while sending Action Frames in standalone AP Mode
Currently, whenever there is a need to transmit an Action frame,
the brcmfmac driver always uses the P2P vif to send the "actframe" IOVAR to
firmware. The P2P interfaces were available when wpa_supplicant is managing
the wlan interface.
However, the P2P interfaces are not created/initialized when only hostapd
is managing the wlan interface. And if hostapd receives an ANQP Query REQ
Action frame even from an un-associated STA, the brcmfmac driver tries
to use an uninitialized P2P vif pointer for sending the IOVAR to firmware.
This NULL pointer dereferencing triggers a driver crash.
[ 1417.074538] Unable to handle kernel NULL pointer dereference at virtual
address 0000000000000000
[...]
[ 1417.075188] Hardware name: Raspberry Pi 4 Model B Rev 1.5 (DT)
[...]
[ 1417.075653] Call trace:
[ 1417.075662] brcmf_p2p_send_action_frame+0x23c/0xc58 [brcmfmac]
[ 1417.075738] brcmf_cfg80211_mgmt_tx+0x304/0x5c0 [brcmfmac]
[ 1417.075810] cfg80211_mlme_mgmt_tx+0x1b0/0x428 [cfg80211]
[ 1417.076067] nl80211_tx_mgmt+0x238/0x388 [cfg80211]
[ 1417.076281] genl_family_rcv_msg_doit+0xe0/0x158
[ 1417.076302] genl_rcv_msg+0x220/0x2a0
[ 1417.076317] netlink_rcv_skb+0x68/0x140
[ 1417.076330] genl_rcv+0x40/0x60
[ 1417.076343] netlink_unicast+0x330/0x3b8
[ 1417.076357] netlink_sendmsg+0x19c/0x3f8
[ 1417.076370] __sock_sendmsg+0x64/0xc0
[ 1417.076391] ____sys_sendmsg+0x268/0x2a0
[ 1417.076408] ___sys_sendmsg+0xb8/0x118
[ 1417.076427] __sys_sendmsg+0x90/0xf8
[ 1417.076445] __arm64_sys_sendmsg+0x2c/0x40
[ 1417.076465] invoke_syscall+0x50/0x120
[ 1417.076486] el0_svc_common.constprop.0+0x48/0xf0
[ 1417.076506] do_el0_svc+0x24/0x38
[ 1417.076525] el0_svc+0x30/0x100
[ 1417.076548] el0t_64_sync_handler+0x100/0x130
[ 1417.076569] el0t_64_sync+0x190/0x198
[ 1417.076589] Code: f9401e80 aa1603e2 f9403be1 5280e483 (f9400000)
Fix this, by always using the vif corresponding to the wdev on which the
Action frame Transmission request was initiated by the userspace. This way,
even if P2P vif is not available, the IOVAR is sent to firmware on AP vif
and the ANQP Query RESP Action frame is transmitted without crashing the
driver.
Move init_completion() for "send_af_done" from brcmf_p2p_create_p2pdev()
to brcmf_p2p_attach(). Because the former function would not get executed
when only hostapd is managing wlan interface, and it is not safe to do
reinit_completion() later in brcmf_p2p_tx_action_frame(), without any prior
init_completion().
And in the brcmf_p2p_tx_action_frame() function, the condition check for
P2P Presence response frame is not needed, since the wpa_supplicant is
properly sending the P2P Presense Response frame on the P2P-GO vif instead
of the P2P-Device vif.
[Cc stable] |
| In the Linux kernel, the following vulnerability has been resolved:
fbdev: udlfb: Fix endpoint check
The syzbot fuzzer detected a problem in the udlfb driver, caused by an
endpoint not having the expected type:
usb 1-1: Read EDID byte 0 failed: -71
usb 1-1: Unable to get valid EDID from device/display
------------[ cut here ]------------
usb 1-1: BOGUS urb xfer, pipe 3 != type 1
WARNING: CPU: 0 PID: 9 at drivers/usb/core/urb.c:504 usb_submit_urb+0xed6/0x1880
drivers/usb/core/urb.c:504
Modules linked in:
CPU: 0 PID: 9 Comm: kworker/0:1 Not tainted
6.4.0-rc1-syzkaller-00016-ga4422ff22142 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google
04/28/2023
Workqueue: usb_hub_wq hub_event
RIP: 0010:usb_submit_urb+0xed6/0x1880 drivers/usb/core/urb.c:504
...
Call Trace:
<TASK>
dlfb_submit_urb+0x92/0x180 drivers/video/fbdev/udlfb.c:1980
dlfb_set_video_mode+0x21f0/0x2950 drivers/video/fbdev/udlfb.c:315
dlfb_ops_set_par+0x2a7/0x8d0 drivers/video/fbdev/udlfb.c:1111
dlfb_usb_probe+0x149a/0x2710 drivers/video/fbdev/udlfb.c:1743
The current approach for this issue failed to catch the problem
because it only checks for the existence of a bulk-OUT endpoint; it
doesn't check whether this endpoint is the one that the driver will
actually use.
We can fix the problem by instead checking that the endpoint used by
the driver does exist and is bulk-OUT. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/mediatek: Fix device use-after-free on unbind
A recent change fixed device reference leaks when looking up drm
platform device driver data during bind() but failed to remove a partial
fix which had been added by commit 80805b62ea5b ("drm/mediatek: Fix
kobject put for component sub-drivers").
This results in a reference imbalance on component bind() failures and
on unbind() which could lead to a user-after-free.
Make sure to only drop the references after retrieving the driver data
by effectively reverting the previous partial fix.
Note that holding a reference to a device does not prevent its driver
data from going away so there is no point in keeping the reference. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Fix stackmap overflow check in __bpf_get_stackid()
Syzkaller reported a KASAN slab-out-of-bounds write in __bpf_get_stackid()
when copying stack trace data. The issue occurs when the perf trace
contains more stack entries than the stack map bucket can hold,
leading to an out-of-bounds write in the bucket's data array. |
| In the Linux kernel, the following vulnerability has been resolved:
accel/amdxdna: Fix an integer overflow in aie2_query_ctx_status_array()
The unpublished smatch static checker reported a warning.
drivers/accel/amdxdna/aie2_pci.c:904 aie2_query_ctx_status_array()
warn: potential user controlled sizeof overflow
'args->num_element * args->element_size' '1-u32max(user) * 1-u32max(user)'
Even this will not cause a real issue, it is better to put a reasonable
limitation for element_size and num_element. Add condition to make sure
the input element_size <= 4K and num_element <= 1K. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Free special fields when update [lru_,]percpu_hash maps
As [lru_,]percpu_hash maps support BPF_KPTR_{REF,PERCPU}, missing
calls to 'bpf_obj_free_fields()' in 'pcpu_copy_value()' could cause the
memory referenced by BPF_KPTR_{REF,PERCPU} fields to be held until the
map gets freed.
Fix this by calling 'bpf_obj_free_fields()' after
'copy_map_value[,_long]()' in 'pcpu_copy_value()'. |
| In the Linux kernel, the following vulnerability has been resolved:
net: sched: act_connmark: initialize struct tc_ife to fix kernel leak
In tcf_connmark_dump(), the variable 'opt' was partially initialized using a
designatied initializer. While the padding bytes are reamined
uninitialized. nla_put() copies the entire structure into a
netlink message, these uninitialized bytes leaked to userspace.
Initialize the structure with memset before assigning its fields
to ensure all members and padding are cleared prior to beign copied. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Fix invalid prog->stats access when update_effective_progs fails
Syzkaller triggers an invalid memory access issue following fault
injection in update_effective_progs. The issue can be described as
follows:
__cgroup_bpf_detach
update_effective_progs
compute_effective_progs
bpf_prog_array_alloc <-- fault inject
purge_effective_progs
/* change to dummy_bpf_prog */
array->items[index] = &dummy_bpf_prog.prog
---softirq start---
__do_softirq
...
__cgroup_bpf_run_filter_skb
__bpf_prog_run_save_cb
bpf_prog_run
stats = this_cpu_ptr(prog->stats)
/* invalid memory access */
flags = u64_stats_update_begin_irqsave(&stats->syncp)
---softirq end---
static_branch_dec(&cgroup_bpf_enabled_key[atype])
The reason is that fault injection caused update_effective_progs to fail
and then changed the original prog into dummy_bpf_prog.prog in
purge_effective_progs. Then a softirq came, and accessing the members of
dummy_bpf_prog.prog in the softirq triggers invalid mem access.
To fix it, skip updating stats when stats is NULL. |
| In the Linux kernel, the following vulnerability has been resolved:
net: phy: micrel: always set shared->phydev for LAN8814
Currently, during the LAN8814 PTP probe shared->phydev is only set if PTP
clock gets actually set, otherwise the function will return before setting
it.
This is an issue as shared->phydev is unconditionally being used when IRQ
is being handled, especially in lan8814_gpio_process_cap and since it was
not set it will cause a NULL pointer exception and crash the kernel.
So, simply always set shared->phydev to avoid the NULL pointer exception. |
| In the Linux kernel, the following vulnerability has been resolved:
isdn: mISDN: hfcsusb: fix memory leak in hfcsusb_probe()
In hfcsusb_probe(), the memory allocated for ctrl_urb gets leaked when
setup_instance() fails with an error code. Fix that by freeing the urb
before freeing the hw structure. Also change the error paths to use the
goto ladder style.
Compile tested only. Issue found using a prototype static analysis tool. |
| In the Linux kernel, the following vulnerability has been resolved:
rv: Fully convert enabled_monitors to use list_head as iterator
The callbacks in enabled_monitors_seq_ops are inconsistent. Some treat the
iterator as struct rv_monitor *, while others treat the iterator as struct
list_head *.
This causes a wrong type cast and crashes the system as reported by Nathan.
Convert everything to use struct list_head * as iterator. This also makes
enabled_monitors consistent with available_monitors. |
| In the Linux kernel, the following vulnerability has been resolved:
mm: prevent poison consumption when splitting THP
When performing memory error injection on a THP (Transparent Huge Page)
mapped to userspace on an x86 server, the kernel panics with the following
trace. The expected behavior is to terminate the affected process instead
of panicking the kernel, as the x86 Machine Check code can recover from an
in-userspace #MC.
mce: [Hardware Error]: CPU 0: Machine Check Exception: f Bank 3: bd80000000070134
mce: [Hardware Error]: RIP 10:<ffffffff8372f8bc> {memchr_inv+0x4c/0xf0}
mce: [Hardware Error]: TSC afff7bbff88a ADDR 1d301b000 MISC 80 PPIN 1e741e77539027db
mce: [Hardware Error]: PROCESSOR 0:d06d0 TIME 1758093249 SOCKET 0 APIC 0 microcode 80000320
mce: [Hardware Error]: Run the above through 'mcelog --ascii'
mce: [Hardware Error]: Machine check: Data load in unrecoverable area of kernel
Kernel panic - not syncing: Fatal local machine check
The root cause of this panic is that handling a memory failure triggered
by an in-userspace #MC necessitates splitting the THP. The splitting
process employs a mechanism, implemented in
try_to_map_unused_to_zeropage(), which reads the pages in the THP to
identify zero-filled pages. However, reading the pages in the THP results
in a second in-kernel #MC, occurring before the initial memory_failure()
completes, ultimately leading to a kernel panic. See the kernel panic
call trace on the two #MCs.
First Machine Check occurs // [1]
memory_failure() // [2]
try_to_split_thp_page()
split_huge_page()
split_huge_page_to_list_to_order()
__folio_split() // [3]
remap_page()
remove_migration_ptes()
remove_migration_pte()
try_to_map_unused_to_zeropage() // [4]
memchr_inv() // [5]
Second Machine Check occurs // [6]
Kernel panic
[1] Triggered by accessing a hardware-poisoned THP in userspace, which is
typically recoverable by terminating the affected process.
[2] Call folio_set_has_hwpoisoned() before try_to_split_thp_page().
[3] Pass the RMP_USE_SHARED_ZEROPAGE remap flag to remap_page().
[4] Try to map the unused THP to zeropage.
[5] Re-access pages in the hw-poisoned THP in the kernel.
[6] Triggered in-kernel, leading to a panic kernel.
In Step[2], memory_failure() sets the poisoned flag on the page in the THP
by TestSetPageHWPoison() before calling try_to_split_thp_page().
As suggested by David Hildenbrand, fix this panic by not accessing to the
poisoned page in the THP during zeropage identification, while continuing
to scan unaffected pages in the THP for possible zeropage mapping. This
prevents a second in-kernel #MC that would cause kernel panic in Step[4].
Thanks to Andrew Zaborowski for his initial work on fixing this issue. |
| In the Linux kernel, the following vulnerability has been resolved:
ntfs3: fix uninit memory after failed mi_read in mi_format_new
Fix a KMSAN un-init bug found by syzkaller.
ntfs_get_bh() expects a buffer from sb_getblk(), that buffer may not be
uptodate. We do not bring the buffer uptodate before setting it as
uptodate. If the buffer were to not be uptodate, it could mean adding a
buffer with un-init data to the mi record. Attempting to load that record
will trigger KMSAN.
Avoid this by setting the buffer as uptodate, if it’s not already, by
overwriting it. |
| In the Linux kernel, the following vulnerability has been resolved:
ntfs3: Fix uninit buffer allocated by __getname()
Fix uninit errors caused after buffer allocation given to 'de'; by
initializing the buffer with zeroes. The fix was found by using KMSAN. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/panthor: Fix kernel panic on partial unmap of a GPU VA region
This commit address a kernel panic issue that can happen if Userspace
tries to partially unmap a GPU virtual region (aka drm_gpuva).
The VM_BIND interface allows partial unmapping of a BO.
Panthor driver pre-allocates memory for the new drm_gpuva structures
that would be needed for the map/unmap operation, done using drm_gpuvm
layer. It expected that only one new drm_gpuva would be needed on umap
but a partial unmap can require 2 new drm_gpuva and that's why it
ended up doing a NULL pointer dereference causing a kernel panic.
Following dump was seen when partial unmap was exercised.
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000078
Mem abort info:
ESR = 0x0000000096000046
EC = 0x25: DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
FSC = 0x06: level 2 translation fault
Data abort info:
ISV = 0, ISS = 0x00000046, ISS2 = 0x00000000
CM = 0, WnR = 1, TnD = 0, TagAccess = 0
GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0
user pgtable: 4k pages, 48-bit VAs, pgdp=000000088a863000
[000000000000078] pgd=080000088a842003, p4d=080000088a842003, pud=0800000884bf5003, pmd=0000000000000000
Internal error: Oops: 0000000096000046 [#1] PREEMPT SMP
<snip>
pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : panthor_gpuva_sm_step_remap+0xe4/0x330 [panthor]
lr : panthor_gpuva_sm_step_remap+0x6c/0x330 [panthor]
sp : ffff800085d43970
x29: ffff800085d43970 x28: ffff00080363e440 x27: ffff0008090c6000
x26: 0000000000000030 x25: ffff800085d439f8 x24: ffff00080d402000
x23: ffff800085d43b60 x22: ffff800085d439e0 x21: ffff00080abdb180
x20: 0000000000000000 x19: 0000000000000000 x18: 0000000000000010
x17: 6e656c202c303030 x16: 3666666666646466 x15: 393d61766f69202c
x14: 312d3d7361203a70 x13: 303030323d6e656c x12: ffff80008324bf58
x11: 0000000000000003 x10: 0000000000000002 x9 : ffff8000801a6a9c
x8 : ffff00080360b300 x7 : 0000000000000000 x6 : 000000088aa35fc7
x5 : fff1000080000000 x4 : ffff8000842ddd30 x3 : 0000000000000001
x2 : 0000000100000000 x1 : 0000000000000001 x0 : 0000000000000078
Call trace:
panthor_gpuva_sm_step_remap+0xe4/0x330 [panthor]
op_remap_cb.isra.22+0x50/0x80
__drm_gpuvm_sm_unmap+0x10c/0x1c8
drm_gpuvm_sm_unmap+0x40/0x60
panthor_vm_exec_op+0xb4/0x3d0 [panthor]
panthor_vm_bind_exec_sync_op+0x154/0x278 [panthor]
panthor_ioctl_vm_bind+0x160/0x4a0 [panthor]
drm_ioctl_kernel+0xbc/0x138
drm_ioctl+0x240/0x500
__arm64_sys_ioctl+0xb0/0xf8
invoke_syscall+0x4c/0x110
el0_svc_common.constprop.1+0x98/0xf8
do_el0_svc+0x24/0x38
el0_svc+0x40/0xf8
el0t_64_sync_handler+0xa0/0xc8
el0t_64_sync+0x174/0x178 |
| In the Linux kernel, the following vulnerability has been resolved:
nvme-core: fix memory leak in dhchap_ctrl_secret
Free dhchap_secret in nvme_ctrl_dhchap_ctrl_secret_store() before we
return when nvme_auth_generate_key() returns error. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: usb-audio: Fix NULL pointer deference in try_to_register_card
In try_to_register_card(), the return value of usb_ifnum_to_if() is
passed directly to usb_interface_claimed() without a NULL check, which
will lead to a NULL pointer dereference when creating an invalid
USB audio device. Fix this by adding a check to ensure the interface
pointer is valid before passing it to usb_interface_claimed(). |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: pcm: Disable bottom softirqs as part of spin_lock_irq() on PREEMPT_RT
snd_pcm_group_lock_irq() acquires a spinlock_t and disables interrupts
via spin_lock_irq(). This also implicitly disables the handling of
softirqs such as TIMER_SOFTIRQ.
On PREEMPT_RT softirqs are preemptible and spin_lock_irq() does not
disable them. That means a timer can be invoked during spin_lock_irq()
on the same CPU. Due to synchronisations reasons local_bh_disable() has
a per-CPU lock named softirq_ctrl.lock which synchronizes individual
softirq against each other.
syz-bot managed to trigger a lockdep report where softirq_ctrl.lock is
acquired in hrtimer_cancel() in addition to hrtimer_run_softirq(). This
is a possible deadlock.
The softirq_ctrl.lock can not be made part of spin_lock_irq() as this
would lead to too much synchronisation against individual threads on the
system. To avoid the possible deadlock, softirqs must be manually
disabled before the lock is acquired.
Disable softirqs before the lock is acquired on PREEMPT_RT. |
| In the Linux kernel, the following vulnerability has been resolved:
can: hi311x: fix null pointer dereference when resuming from sleep before interface was enabled
This issue is similar to the vulnerability in the `mcp251x` driver,
which was fixed in commit 03c427147b2d ("can: mcp251x: fix resume from
sleep before interface was brought up").
In the `hi311x` driver, when the device resumes from sleep, the driver
schedules `priv->restart_work`. However, if the network interface was
not previously enabled, the `priv->wq` (workqueue) is not allocated and
initialized, leading to a null pointer dereference.
To fix this, we move the allocation and initialization of the workqueue
from the `hi3110_open` function to the `hi3110_can_probe` function.
This ensures that the workqueue is properly initialized before it is
used during device resume. And added logic to destroy the workqueue
in the error handling paths of `hi3110_can_probe` and in the
`hi3110_can_remove` function to prevent resource leaks. |
| In the Linux kernel, the following vulnerability has been resolved:
PCI/AER: Fix NULL pointer access by aer_info
The kzalloc(GFP_KERNEL) may return NULL, so all accesses to aer_info->xxx
will result in kernel panic. Fix it. |
