| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
net: nsh: Use correct mac_offset to unwind gso skb in nsh_gso_segment()
As the call trace shows, skb_panic was caused by wrong skb->mac_header
in nsh_gso_segment():
invalid opcode: 0000 [#1] PREEMPT SMP KASAN PTI
CPU: 3 PID: 2737 Comm: syz Not tainted 6.3.0-next-20230505 #1
RIP: 0010:skb_panic+0xda/0xe0
call Trace:
skb_push+0x91/0xa0
nsh_gso_segment+0x4f3/0x570
skb_mac_gso_segment+0x19e/0x270
__skb_gso_segment+0x1e8/0x3c0
validate_xmit_skb+0x452/0x890
validate_xmit_skb_list+0x99/0xd0
sch_direct_xmit+0x294/0x7c0
__dev_queue_xmit+0x16f0/0x1d70
packet_xmit+0x185/0x210
packet_snd+0xc15/0x1170
packet_sendmsg+0x7b/0xa0
sock_sendmsg+0x14f/0x160
The root cause is:
nsh_gso_segment() use skb->network_header - nhoff to reset mac_header
in skb_gso_error_unwind() if inner-layer protocol gso fails.
However, skb->network_header may be reset by inner-layer protocol
gso function e.g. mpls_gso_segment. skb->mac_header reset by the
inaccurate network_header will be larger than skb headroom.
nsh_gso_segment
nhoff = skb->network_header - skb->mac_header;
__skb_pull(skb,nsh_len)
skb_mac_gso_segment
mpls_gso_segment
skb_reset_network_header(skb);//skb->network_header+=nsh_len
return -EINVAL;
skb_gso_error_unwind
skb_push(skb, nsh_len);
skb->mac_header = skb->network_header - nhoff;
// skb->mac_header > skb->headroom, cause skb_push panic
Use correct mac_offset to restore mac_header and get rid of nhoff. |
| In the Linux kernel, the following vulnerability has been resolved:
can: isotp: check CAN address family in isotp_bind()
Add missing check to block non-AF_CAN binds.
Syzbot created some code which matched the right sockaddr struct size
but used AF_XDP (0x2C) instead of AF_CAN (0x1D) in the address family
field:
bind$xdp(r2, &(0x7f0000000540)={0x2c, 0x0, r4, 0x0, r2}, 0x10)
^^^^
This has no funtional impact but the userspace should be notified about
the wrong address family field content. |
| In the Linux kernel, the following vulnerability has been resolved:
idpf: fix possible vport_config NULL pointer deref in remove
Attempting to remove the driver will cause a crash in cases where
the vport failed to initialize. Following trace is from an instance where
the driver failed during an attempt to create a VF:
[ 1661.543624] idpf 0000:84:00.7: Device HW Reset initiated
[ 1722.923726] idpf 0000:84:00.7: Transaction timed-out (op:1 cookie:2900 vc_op:1 salt:29 timeout:60000ms)
[ 1723.353263] BUG: kernel NULL pointer dereference, address: 0000000000000028
...
[ 1723.358472] RIP: 0010:idpf_remove+0x11c/0x200 [idpf]
...
[ 1723.364973] Call Trace:
[ 1723.365475] <TASK>
[ 1723.365972] pci_device_remove+0x42/0xb0
[ 1723.366481] device_release_driver_internal+0x1a9/0x210
[ 1723.366987] pci_stop_bus_device+0x6d/0x90
[ 1723.367488] pci_stop_and_remove_bus_device+0x12/0x20
[ 1723.367971] pci_iov_remove_virtfn+0xbd/0x120
[ 1723.368309] sriov_disable+0x34/0xe0
[ 1723.368643] idpf_sriov_configure+0x58/0x140 [idpf]
[ 1723.368982] sriov_numvfs_store+0xda/0x1c0
Avoid the NULL pointer dereference by adding NULL pointer check for
vport_config[i], before freeing user_config.q_coalesce. |
| In the Linux kernel, the following vulnerability has been resolved:
nouveau/firmware: Add missing kfree() of nvkm_falcon_fw::boot
nvkm_falcon_fw::boot is allocated, but no one frees it. This causes a
kmemleak warning.
Make sure this data is deallocated. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdkfd: Fix mmap write lock not release
If mmap write lock is taken while draining retry fault, mmap write lock
is not released because svm_range_restore_pages calls mmap_read_unlock
then returns. This causes deadlock and system hangs later because mmap
read or write lock cannot be taken.
Downgrade mmap write lock to read lock if draining retry fault fix this
bug. |
| In the Linux kernel, the following vulnerability has been resolved:
net: dsa: microchip: Don't free uninitialized ksz_irq
If something goes wrong at setup, ksz_irq_free() can be called on
uninitialized ksz_irq (for example when ksz_ptp_irq_setup() fails). It
leads to freeing uninitialized IRQ numbers and/or domains.
Use dsa_switch_for_each_user_port_continue_reverse() in the error path
to iterate only over the fully initialized ports. |
| In the Linux kernel, the following vulnerability has been resolved:
fs/namespace: fix reference leak in grab_requested_mnt_ns
lookup_mnt_ns() already takes a reference on mnt_ns.
grab_requested_mnt_ns() doesn't need to take an extra reference. |
| In the Linux kernel, the following vulnerability has been resolved:
can: gs_usb: gs_usb_receive_bulk_callback(): check actual_length before accessing data
The URB received in gs_usb_receive_bulk_callback() contains a struct
gs_host_frame. The length of the data after the header depends on the
gs_host_frame hf::flags and the active device features (e.g. time
stamping).
Introduce a new function gs_usb_get_minimum_length() and check that we have
at least received the required amount of data before accessing it. Only
copy the data to that skb that has actually been received.
[mkl: rename gs_usb_get_minimum_length() -> +gs_usb_get_minimum_rx_length()] |
| NVIDIA Display Driver for Windows and Linux contains a vulnerability in a video decoder, where an attacker might cause an out-of-bounds read. A successful exploit of this vulnerability might lead to information disclosure or denial of service. |
| NVIDIA Display Driver for Linux contains a vulnerability in a kernel module, where an attacker might be able to trigger a null pointer deference. A successful exploit of this vulnerability might lead to denial of service. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/msm: Fix pgtable prealloc error path
The following splat was reported:
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000010
Mem abort info:
ESR = 0x0000000096000004
EC = 0x25: DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
FSC = 0x04: level 0 translation fault
Data abort info:
ISV = 0, ISS = 0x00000004, ISS2 = 0x00000000
CM = 0, WnR = 0, TnD = 0, TagAccess = 0
GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0
user pgtable: 4k pages, 48-bit VAs, pgdp=00000008d0fd8000
[0000000000000010] pgd=0000000000000000, p4d=0000000000000000
Internal error: Oops: 0000000096000004 [#1] SMP
CPU: 5 UID: 1000 PID: 149076 Comm: Xwayland Tainted: G S 6.16.0-rc2-00809-g0b6974bb4134-dirty #367 PREEMPT
Tainted: [S]=CPU_OUT_OF_SPEC
Hardware name: Qualcomm Technologies, Inc. SM8650 HDK (DT)
pstate: 83400005 (Nzcv daif +PAN -UAO +TCO +DIT -SSBS BTYPE=--)
pc : build_detached_freelist+0x28/0x224
lr : kmem_cache_free_bulk.part.0+0x38/0x244
sp : ffff000a508c7a20
x29: ffff000a508c7a20 x28: ffff000a508c7d50 x27: ffffc4e49d16f350
x26: 0000000000000058 x25: 00000000fffffffc x24: 0000000000000000
x23: ffff00098c4e1450 x22: 00000000fffffffc x21: 0000000000000000
x20: ffff000a508c7af8 x19: 0000000000000002 x18: 00000000000003e8
x17: ffff000809523850 x16: ffff000809523820 x15: 0000000000401640
x14: ffff000809371140 x13: 0000000000000130 x12: ffff0008b5711e30
x11: 00000000001058fa x10: 0000000000000a80 x9 : ffff000a508c7940
x8 : ffff000809371ba0 x7 : 781fffe033087fff x6 : 0000000000000000
x5 : ffff0008003cd000 x4 : 781fffe033083fff x3 : ffff000a508c7af8
x2 : fffffdffc0000000 x1 : 0001000000000000 x0 : ffff0008001a6a00
Call trace:
build_detached_freelist+0x28/0x224 (P)
kmem_cache_free_bulk.part.0+0x38/0x244
kmem_cache_free_bulk+0x10/0x1c
msm_iommu_pagetable_prealloc_cleanup+0x3c/0xd0
msm_vma_job_free+0x30/0x240
msm_ioctl_vm_bind+0x1d0/0x9a0
drm_ioctl_kernel+0x84/0x104
drm_ioctl+0x358/0x4d4
__arm64_sys_ioctl+0x8c/0xe0
invoke_syscall+0x44/0x100
el0_svc_common.constprop.0+0x3c/0xe0
do_el0_svc+0x18/0x20
el0_svc+0x30/0x100
el0t_64_sync_handler+0x104/0x130
el0t_64_sync+0x170/0x174
Code: aa0203f5 b26287e2 f2dfbfe2 aa0303f4 (f8737ab6)
---[ end trace 0000000000000000 ]---
Since msm_vma_job_free() is called directly from the ioctl, this looks
like an error path cleanup issue. Which I think results from
prealloc_cleanup() called without a preceding successful
prealloc_allocate() call. So handle that case better.
Patchwork: https://patchwork.freedesktop.org/patch/678677/ |
| In the Linux kernel, the following vulnerability has been resolved:
media: iris: fix module removal if firmware download failed
Fix remove if firmware failed to load:
qcom-iris aa00000.video-codec: Direct firmware load for qcom/vpu/vpu33_p4.mbn failed with error -2
qcom-iris aa00000.video-codec: firmware download failed
qcom-iris aa00000.video-codec: core init failed
then:
$ echo aa00000.video-codec > /sys/bus/platform/drivers/qcom-iris/unbind
Triggers:
genpd genpd:1:aa00000.video-codec: Runtime PM usage count underflow!
------------[ cut here ]------------
video_cc_mvs0_clk already disabled
WARNING: drivers/clk/clk.c:1206 at clk_core_disable+0xa4/0xac, CPU#1: sh/542
<snip>
pc : clk_core_disable+0xa4/0xac
lr : clk_core_disable+0xa4/0xac
<snip>
Call trace:
clk_core_disable+0xa4/0xac (P)
clk_disable+0x30/0x4c
iris_disable_unprepare_clock+0x20/0x48 [qcom_iris]
iris_vpu_power_off_hw+0x48/0x58 [qcom_iris]
iris_vpu33_power_off_hardware+0x44/0x230 [qcom_iris]
iris_vpu_power_off+0x34/0x84 [qcom_iris]
iris_core_deinit+0x44/0xc8 [qcom_iris]
iris_remove+0x20/0x48 [qcom_iris]
platform_remove+0x20/0x30
device_remove+0x4c/0x80
<snip>
---[ end trace 0000000000000000 ]---
------------[ cut here ]------------
video_cc_mvs0_clk already unprepared
WARNING: drivers/clk/clk.c:1065 at clk_core_unprepare+0xf0/0x110, CPU#2: sh/542
<snip>
pc : clk_core_unprepare+0xf0/0x110
lr : clk_core_unprepare+0xf0/0x110
<snip>
Call trace:
clk_core_unprepare+0xf0/0x110 (P)
clk_unprepare+0x2c/0x44
iris_disable_unprepare_clock+0x28/0x48 [qcom_iris]
iris_vpu_power_off_hw+0x48/0x58 [qcom_iris]
iris_vpu33_power_off_hardware+0x44/0x230 [qcom_iris]
iris_vpu_power_off+0x34/0x84 [qcom_iris]
iris_core_deinit+0x44/0xc8 [qcom_iris]
iris_remove+0x20/0x48 [qcom_iris]
platform_remove+0x20/0x30
device_remove+0x4c/0x80
<snip>
---[ end trace 0000000000000000 ]---
genpd genpd:0:aa00000.video-codec: Runtime PM usage count underflow!
------------[ cut here ]------------
gcc_video_axi0_clk already disabled
WARNING: drivers/clk/clk.c:1206 at clk_core_disable+0xa4/0xac, CPU#4: sh/542
<snip>
pc : clk_core_disable+0xa4/0xac
lr : clk_core_disable+0xa4/0xac
<snip>
Call trace:
clk_core_disable+0xa4/0xac (P)
clk_disable+0x30/0x4c
iris_disable_unprepare_clock+0x20/0x48 [qcom_iris]
iris_vpu33_power_off_controller+0x17c/0x428 [qcom_iris]
iris_vpu_power_off+0x48/0x84 [qcom_iris]
iris_core_deinit+0x44/0xc8 [qcom_iris]
iris_remove+0x20/0x48 [qcom_iris]
platform_remove+0x20/0x30
device_remove+0x4c/0x80
<snip>
------------[ cut here ]------------
gcc_video_axi0_clk already unprepared
WARNING: drivers/clk/clk.c:1065 at clk_core_unprepare+0xf0/0x110, CPU#4: sh/542
<snip>
pc : clk_core_unprepare+0xf0/0x110
lr : clk_core_unprepare+0xf0/0x110
<snip>
Call trace:
clk_core_unprepare+0xf0/0x110 (P)
clk_unprepare+0x2c/0x44
iris_disable_unprepare_clock+0x28/0x48 [qcom_iris]
iris_vpu33_power_off_controller+0x17c/0x428 [qcom_iris]
iris_vpu_power_off+0x48/0x84 [qcom_iris]
iris_core_deinit+0x44/0xc8 [qcom_iris]
iris_remove+0x20/0x48 [qcom_iris]
platform_remove+0x20/0x30
device_remove+0x4c/0x80
<snip>
---[ end trace 0000000000000000 ]---
Skip deinit if initialization never succeeded. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: lpfc: Prevent lpfc_debugfs_lockstat_write() buffer overflow
A static code analysis tool flagged the possibility of buffer overflow when
using copy_from_user() for a debugfs entry.
Currently, it is possible that copy_from_user() copies more bytes than what
would fit in the mybuf char array. Add a min() restriction check between
sizeof(mybuf) - 1 and nbytes passed from the userspace buffer to protect
against buffer overflow. |
| Uncontrolled resource consumption in the Linux kernel-mode driver for some Intel(R) 700 Series Ethernet before version 2.28.5 may allow an authenticated user to potentially enable denial of service. |
| Insufficient control flow management in the Linux kernel-mode driver for some Intel(R) 700 Series Ethernet before version 2.28.5 may allow an authenticated user to potentially enable escalation of privilege via local access. |
| In the Linux kernel, the following vulnerability has been resolved:
fs: Protect reconfiguration of sb read-write from racing writes
The reconfigure / remount code takes a lot of effort to protect
filesystem's reconfiguration code from racing writes on remounting
read-only. However during remounting read-only filesystem to read-write
mode userspace writes can start immediately once we clear SB_RDONLY
flag. This is inconvenient for example for ext4 because we need to do
some writes to the filesystem (such as preparation of quota files)
before we can take userspace writes so we are clearing SB_RDONLY flag
before we are fully ready to accept userpace writes and syzbot has found
a way to exploit this [1]. Also as far as I'm reading the code
the filesystem remount code was protected from racing writes in the
legacy mount path by the mount's MNT_READONLY flag so this is relatively
new problem. It is actually fairly easy to protect remount read-write
from racing writes using sb->s_readonly_remount flag so let's just do
that instead of having to workaround these races in the filesystem code.
[1] https://lore.kernel.org/all/00000000000006a0df05f6667499@google.com/T/ |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: essiv - Check ssize for decryption and in-place encryption
Move the ssize check to the start in essiv_aead_crypt so that
it's also checked for decryption and in-place encryption. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: do not run mt76u_status_worker if the device is not running
Fix the following NULL pointer dereference avoiding to run
mt76u_status_worker thread if the device is not running yet.
KASAN: null-ptr-deref in range
[0x0000000000000000-0x0000000000000007]
CPU: 0 PID: 98 Comm: kworker/u2:2 Not tainted 5.14.0+ #78 Hardware
name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS
rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014
Workqueue: mt76 mt76u_tx_status_data
RIP: 0010:mt76x02_mac_fill_tx_status.isra.0+0x82c/0x9e0
Code: c5 48 b8 00 00 00 00 00 fc ff df 80 3c 02 00 0f 85 94 01 00 00
48 b8 00 00 00 00 00 fc ff df 4d 8b 34 24 4c 89 f2 48 c1 ea 03 <0f>
b6
04 02 84 c0 74 08 3c 03 0f 8e 89 01 00 00 41 8b 16 41 0f b7
RSP: 0018:ffffc900005af988 EFLAGS: 00010246
RAX: dffffc0000000000 RBX: ffffc900005afae8 RCX: 0000000000000000
RDX: 0000000000000000 RSI: ffffffff832fc661 RDI: ffffc900005afc2a
RBP: ffffc900005afae0 R08: 0000000000000001 R09: fffff520000b5f3c
R10: 0000000000000003 R11: fffff520000b5f3b R12: ffff88810b6132d8
R13: 000000000000ffff R14: 0000000000000000 R15: ffffc900005afc28
FS: 0000000000000000(0000) GS:ffff88811aa00000(0000)
knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fa0eda6a000 CR3: 0000000118f17000 CR4: 0000000000750ef0
PKRU: 55555554
Call Trace:
mt76x02_send_tx_status+0x1d2/0xeb0
mt76x02_tx_status_data+0x8e/0xd0
mt76u_tx_status_data+0xe1/0x240
process_one_work+0x92b/0x1460
worker_thread+0x95/0xe00
kthread+0x3a1/0x480
ret_from_fork+0x1f/0x30
Modules linked in:
--[ end trace 8df5d20fc5040f65 ]--
RIP: 0010:mt76x02_mac_fill_tx_status.isra.0+0x82c/0x9e0
Code: c5 48 b8 00 00 00 00 00 fc ff df 80 3c 02 00 0f 85 94 01 00 00
48 b8 00 00 00 00 00 fc ff df 4d 8b 34 24 4c 89 f2 48 c1 ea 03 <0f>
b6
04 02 84 c0 74 08 3c 03 0f 8e 89 01 00 00 41 8b 16 41 0f b7
RSP: 0018:ffffc900005af988 EFLAGS: 00010246
RAX: dffffc0000000000 RBX: ffffc900005afae8 RCX: 0000000000000000
RDX: 0000000000000000 RSI: ffffffff832fc661 RDI: ffffc900005afc2a
RBP: ffffc900005afae0 R08: 0000000000000001 R09: fffff520000b5f3c
R10: 0000000000000003 R11: fffff520000b5f3b R12: ffff88810b6132d8
R13: 000000000000ffff R14: 0000000000000000 R15: ffffc900005afc28
FS: 0000000000000000(0000) GS:ffff88811aa00000(0000)
knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fa0eda6a000 CR3: 0000000118f17000 CR4: 0000000000750ef0
PKRU: 55555554
Moreover move stat_work schedule out of the for loop. |
| In the Linux kernel, the following vulnerability has been resolved:
9p/trans_fd: p9_fd_request: kick rx thread if EPOLLIN
p9_read_work() doesn't set Rworksched and doesn't do schedule_work(m->rq)
if list_empty(&m->req_list).
However, if the pipe is full, we need to read more data and this used to
work prior to commit aaec5a95d59615 ("pipe_read: don't wake up the writer
if the pipe is still full").
p9_read_work() does p9_fd_read() -> ... -> anon_pipe_read() which (before
the commit above) triggered the unnecessary wakeup. This wakeup calls
p9_pollwake() which kicks p9_poll_workfn() -> p9_poll_mux(), p9_poll_mux()
will notice EPOLLIN and schedule_work(&m->rq).
This no longer happens after the optimization above, change p9_fd_request()
to use p9_poll_mux() instead of only checking for EPOLLOUT. |
| In the Linux kernel, the following vulnerability has been resolved:
serial: sprd: Fix DMA buffer leak issue
Release DMA buffer when _probe() returns failure to avoid memory leak. |
