| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
i40e: Fix DMA mappings leak
During reallocation of RX buffers, new DMA mappings are created for
those buffers.
steps for reproduction:
while :
do
for ((i=0; i<=8160; i=i+32))
do
ethtool -G enp130s0f0 rx $i tx $i
sleep 0.5
ethtool -g enp130s0f0
done
done
This resulted in crash:
i40e 0000:01:00.1: Unable to allocate memory for the Rx descriptor ring, size=65536
Driver BUG
WARNING: CPU: 0 PID: 4300 at net/core/xdp.c:141 xdp_rxq_info_unreg+0x43/0x50
Call Trace:
i40e_free_rx_resources+0x70/0x80 [i40e]
i40e_set_ringparam+0x27c/0x800 [i40e]
ethnl_set_rings+0x1b2/0x290
genl_family_rcv_msg_doit.isra.15+0x10f/0x150
genl_family_rcv_msg+0xb3/0x160
? rings_fill_reply+0x1a0/0x1a0
genl_rcv_msg+0x47/0x90
? genl_family_rcv_msg+0x160/0x160
netlink_rcv_skb+0x4c/0x120
genl_rcv+0x24/0x40
netlink_unicast+0x196/0x230
netlink_sendmsg+0x204/0x3d0
sock_sendmsg+0x4c/0x50
__sys_sendto+0xee/0x160
? handle_mm_fault+0xbe/0x1e0
? syscall_trace_enter+0x1d3/0x2c0
__x64_sys_sendto+0x24/0x30
do_syscall_64+0x5b/0x1a0
entry_SYSCALL_64_after_hwframe+0x65/0xca
RIP: 0033:0x7f5eac8b035b
Missing register, driver bug
WARNING: CPU: 0 PID: 4300 at net/core/xdp.c:119 xdp_rxq_info_unreg_mem_model+0x69/0x140
Call Trace:
xdp_rxq_info_unreg+0x1e/0x50
i40e_free_rx_resources+0x70/0x80 [i40e]
i40e_set_ringparam+0x27c/0x800 [i40e]
ethnl_set_rings+0x1b2/0x290
genl_family_rcv_msg_doit.isra.15+0x10f/0x150
genl_family_rcv_msg+0xb3/0x160
? rings_fill_reply+0x1a0/0x1a0
genl_rcv_msg+0x47/0x90
? genl_family_rcv_msg+0x160/0x160
netlink_rcv_skb+0x4c/0x120
genl_rcv+0x24/0x40
netlink_unicast+0x196/0x230
netlink_sendmsg+0x204/0x3d0
sock_sendmsg+0x4c/0x50
__sys_sendto+0xee/0x160
? handle_mm_fault+0xbe/0x1e0
? syscall_trace_enter+0x1d3/0x2c0
__x64_sys_sendto+0x24/0x30
do_syscall_64+0x5b/0x1a0
entry_SYSCALL_64_after_hwframe+0x65/0xca
RIP: 0033:0x7f5eac8b035b
This was caused because of new buffers with different RX ring count should
substitute older ones, but those buffers were freed in
i40e_configure_rx_ring and reallocated again with i40e_alloc_rx_bi,
thus kfree on rx_bi caused leak of already mapped DMA.
Fix this by reallocating ZC with rx_bi_zc struct when BPF program loads. Additionally
reallocate back to rx_bi when BPF program unloads.
If BPF program is loaded/unloaded and XSK pools are created, reallocate
RX queues accordingly in XSP_SETUP_XSK_POOL handler. |
| In the Linux kernel before 4.8, usb_parse_endpoint in drivers/usb/core/config.c does not validate the wMaxPacketSize field of an endpoint descriptor. NOTE: This vulnerability only affects products that are no longer supported by the supplier. |
| In the Linux kernel, the following vulnerability has been resolved:
xtensa: simdisk: add input size check in proc_write_simdisk
A malicious user could pass an arbitrarily bad value
to memdup_user_nul(), potentially causing kernel crash.
This follows the same pattern as commit ee76746387f6
("netdevsim: prevent bad user input in nsim_dev_health_break_write()") |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: fix race when deleting quota root from the dirty cow roots list
When disabling quotas we are deleting the quota root from the list
fs_info->dirty_cowonly_roots without taking the lock that protects it,
which is struct btrfs_fs_info::trans_lock. This unsynchronized list
manipulation may cause chaos if there's another concurrent manipulation
of this list, such as when adding a root to it with
ctree.c:add_root_to_dirty_list().
This can result in all sorts of weird failures caused by a race, such as
the following crash:
[337571.278245] general protection fault, probably for non-canonical address 0xdead000000000108: 0000 [#1] PREEMPT SMP PTI
[337571.278933] CPU: 1 PID: 115447 Comm: btrfs Tainted: G W 6.4.0-rc6-btrfs-next-134+ #1
[337571.279153] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.14.0-0-g155821a1990b-prebuilt.qemu.org 04/01/2014
[337571.279572] RIP: 0010:commit_cowonly_roots+0x11f/0x250 [btrfs]
[337571.279928] Code: 85 38 06 00 (...)
[337571.280363] RSP: 0018:ffff9f63446efba0 EFLAGS: 00010206
[337571.280582] RAX: ffff942d98ec2638 RBX: ffff9430b82b4c30 RCX: 0000000449e1c000
[337571.280798] RDX: dead000000000100 RSI: ffff9430021e4900 RDI: 0000000000036070
[337571.281015] RBP: ffff942d98ec2000 R08: ffff942d98ec2000 R09: 000000000000015b
[337571.281254] R10: 0000000000000009 R11: 0000000000000001 R12: ffff942fe8fbf600
[337571.281476] R13: ffff942dabe23040 R14: ffff942dabe20800 R15: ffff942d92cf3b48
[337571.281723] FS: 00007f478adb7340(0000) GS:ffff94349fa40000(0000) knlGS:0000000000000000
[337571.281950] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[337571.282184] CR2: 00007f478ab9a3d5 CR3: 000000001e02c001 CR4: 0000000000370ee0
[337571.282416] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[337571.282647] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[337571.282874] Call Trace:
[337571.283101] <TASK>
[337571.283327] ? __die_body+0x1b/0x60
[337571.283570] ? die_addr+0x39/0x60
[337571.283796] ? exc_general_protection+0x22e/0x430
[337571.284022] ? asm_exc_general_protection+0x22/0x30
[337571.284251] ? commit_cowonly_roots+0x11f/0x250 [btrfs]
[337571.284531] btrfs_commit_transaction+0x42e/0xf90 [btrfs]
[337571.284803] ? _raw_spin_unlock+0x15/0x30
[337571.285031] ? release_extent_buffer+0x103/0x130 [btrfs]
[337571.285305] reset_balance_state+0x152/0x1b0 [btrfs]
[337571.285578] btrfs_balance+0xa50/0x11e0 [btrfs]
[337571.285864] ? __kmem_cache_alloc_node+0x14a/0x410
[337571.286086] btrfs_ioctl+0x249a/0x3320 [btrfs]
[337571.286358] ? mod_objcg_state+0xd2/0x360
[337571.286577] ? refill_obj_stock+0xb0/0x160
[337571.286798] ? seq_release+0x25/0x30
[337571.287016] ? __rseq_handle_notify_resume+0x3ba/0x4b0
[337571.287235] ? percpu_counter_add_batch+0x2e/0xa0
[337571.287455] ? __x64_sys_ioctl+0x88/0xc0
[337571.287675] __x64_sys_ioctl+0x88/0xc0
[337571.287901] do_syscall_64+0x38/0x90
[337571.288126] entry_SYSCALL_64_after_hwframe+0x72/0xdc
[337571.288352] RIP: 0033:0x7f478aaffe9b
So fix this by locking struct btrfs_fs_info::trans_lock before deleting
the quota root from that list. |
| In the Linux kernel, the following vulnerability has been resolved:
media: mc: Clear minor number before put device
The device minor should not be cleared after the device is released. |
| In the Linux kernel, the following vulnerability has been resolved:
f2fs: fix to truncate first page in error path of f2fs_truncate()
syzbot reports a bug as below:
loop0: detected capacity change from 0 to 40427
F2FS-fs (loop0): Wrong SSA boundary, start(3584) end(4096) blocks(3072)
F2FS-fs (loop0): Can't find valid F2FS filesystem in 1th superblock
F2FS-fs (loop0): invalid crc value
F2FS-fs (loop0): f2fs_convert_inline_folio: corrupted inline inode ino=3, i_addr[0]:0x1601, run fsck to fix.
------------[ cut here ]------------
kernel BUG at fs/inode.c:753!
RIP: 0010:clear_inode+0x169/0x190 fs/inode.c:753
Call Trace:
<TASK>
evict+0x504/0x9c0 fs/inode.c:810
f2fs_fill_super+0x5612/0x6fa0 fs/f2fs/super.c:5047
get_tree_bdev_flags+0x40e/0x4d0 fs/super.c:1692
vfs_get_tree+0x8f/0x2b0 fs/super.c:1815
do_new_mount+0x2a2/0x9e0 fs/namespace.c:3808
do_mount fs/namespace.c:4136 [inline]
__do_sys_mount fs/namespace.c:4347 [inline]
__se_sys_mount+0x317/0x410 fs/namespace.c:4324
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0xfa/0x3b0 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x77/0x7f
During f2fs_evict_inode(), clear_inode() detects that we missed to truncate
all page cache before destorying inode, that is because in below path, we
will create page #0 in cache, but missed to drop it in error path, let's fix
it.
- evict
- f2fs_evict_inode
- f2fs_truncate
- f2fs_convert_inline_inode
- f2fs_grab_cache_folio
: create page #0 in cache
- f2fs_convert_inline_folio
: sanity check failed, return -EFSCORRUPTED
- clear_inode detects that inode->i_data.nrpages is not zero |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: mpi3mr: Fix an issue found by KASAN
Write only correct size (32 instead of 64 bytes). |
| In the Linux kernel, the following vulnerability has been resolved:
clk: st: Fix memory leak in st_of_quadfs_setup()
If st_clk_register_quadfs_pll() fails, @lock should be freed before goto
@err_exit, otherwise will cause meory leak issue, fix it. |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: fix bug_on in __es_tree_search caused by bad quota inode
We got a issue as fllows:
==================================================================
kernel BUG at fs/ext4/extents_status.c:202!
invalid opcode: 0000 [#1] PREEMPT SMP
CPU: 1 PID: 810 Comm: mount Not tainted 6.1.0-rc1-next-g9631525255e3 #352
RIP: 0010:__es_tree_search.isra.0+0xb8/0xe0
RSP: 0018:ffffc90001227900 EFLAGS: 00010202
RAX: 0000000000000000 RBX: 0000000077512a0f RCX: 0000000000000000
RDX: 0000000000000002 RSI: 0000000000002a10 RDI: ffff8881004cd0c8
RBP: ffff888177512ac8 R08: 47ffffffffffffff R09: 0000000000000001
R10: 0000000000000001 R11: 00000000000679af R12: 0000000000002a10
R13: ffff888177512d88 R14: 0000000077512a10 R15: 0000000000000000
FS: 00007f4bd76dbc40(0000)GS:ffff88842fd00000(0000)knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00005653bf993cf8 CR3: 000000017bfdf000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
ext4_es_cache_extent+0xe2/0x210
ext4_cache_extents+0xd2/0x110
ext4_find_extent+0x5d5/0x8c0
ext4_ext_map_blocks+0x9c/0x1d30
ext4_map_blocks+0x431/0xa50
ext4_getblk+0x82/0x340
ext4_bread+0x14/0x110
ext4_quota_read+0xf0/0x180
v2_read_header+0x24/0x90
v2_check_quota_file+0x2f/0xa0
dquot_load_quota_sb+0x26c/0x760
dquot_load_quota_inode+0xa5/0x190
ext4_enable_quotas+0x14c/0x300
__ext4_fill_super+0x31cc/0x32c0
ext4_fill_super+0x115/0x2d0
get_tree_bdev+0x1d2/0x360
ext4_get_tree+0x19/0x30
vfs_get_tree+0x26/0xe0
path_mount+0x81d/0xfc0
do_mount+0x8d/0xc0
__x64_sys_mount+0xc0/0x160
do_syscall_64+0x35/0x80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
</TASK>
==================================================================
Above issue may happen as follows:
-------------------------------------
ext4_fill_super
ext4_orphan_cleanup
ext4_enable_quotas
ext4_quota_enable
ext4_iget --> get error inode <5>
ext4_ext_check_inode --> Wrong imode makes it escape inspection
make_bad_inode(inode) --> EXT4_BOOT_LOADER_INO set imode
dquot_load_quota_inode
vfs_setup_quota_inode --> check pass
dquot_load_quota_sb
v2_check_quota_file
v2_read_header
ext4_quota_read
ext4_bread
ext4_getblk
ext4_map_blocks
ext4_ext_map_blocks
ext4_find_extent
ext4_cache_extents
ext4_es_cache_extent
__es_tree_search.isra.0
ext4_es_end --> Wrong extents trigger BUG_ON
In the above issue, s_usr_quota_inum is set to 5, but inode<5> contains
incorrect imode and disordered extents. Because 5 is EXT4_BOOT_LOADER_INO,
the ext4_ext_check_inode check in the ext4_iget function can be bypassed,
finally, the extents that are not checked trigger the BUG_ON in the
__es_tree_search function. To solve this issue, check whether the inode is
bad_inode in vfs_setup_quota_inode(). |
| In the Linux kernel, the following vulnerability has been resolved:
ice: prevent NULL pointer deref during reload
Calling ethtool during reload can lead to call trace, because VSI isn't
configured for some time, but netdev is alive.
To fix it add rtnl lock for VSI deconfig and config. Set ::num_q_vectors
to 0 after freeing and add a check for ::tx/rx_rings in ring related
ethtool ops.
Add proper unroll of filters in ice_start_eth().
Reproduction:
$watch -n 0.1 -d 'ethtool -g enp24s0f0np0'
$devlink dev reload pci/0000:18:00.0 action driver_reinit
Call trace before fix:
[66303.926205] BUG: kernel NULL pointer dereference, address: 0000000000000000
[66303.926259] #PF: supervisor read access in kernel mode
[66303.926286] #PF: error_code(0x0000) - not-present page
[66303.926311] PGD 0 P4D 0
[66303.926332] Oops: 0000 [#1] PREEMPT SMP PTI
[66303.926358] CPU: 4 PID: 933821 Comm: ethtool Kdump: loaded Tainted: G OE 6.4.0-rc5+ #1
[66303.926400] Hardware name: Intel Corporation S2600WFT/S2600WFT, BIOS SE5C620.86B.00.01.0014.070920180847 07/09/2018
[66303.926446] RIP: 0010:ice_get_ringparam+0x22/0x50 [ice]
[66303.926649] Code: 90 90 90 90 90 90 90 90 f3 0f 1e fa 0f 1f 44 00 00 48 8b 87 c0 09 00 00 c7 46 04 e0 1f 00 00 c7 46 10 e0 1f 00 00 48 8b 50 20 <48> 8b 12 0f b7 52 3a 89 56 14 48 8b 40 28 48 8b 00 0f b7 40 58 48
[66303.926722] RSP: 0018:ffffad40472f39c8 EFLAGS: 00010246
[66303.926749] RAX: ffff98a8ada05828 RBX: ffff98a8c46dd060 RCX: ffffad40472f3b48
[66303.926781] RDX: 0000000000000000 RSI: ffff98a8c46dd068 RDI: ffff98a8b23c4000
[66303.926811] RBP: ffffad40472f3b48 R08: 00000000000337b0 R09: 0000000000000000
[66303.926843] R10: 0000000000000001 R11: 0000000000000100 R12: ffff98a8b23c4000
[66303.926874] R13: ffff98a8c46dd060 R14: 000000000000000f R15: ffffad40472f3a50
[66303.926906] FS: 00007f6397966740(0000) GS:ffff98b390900000(0000) knlGS:0000000000000000
[66303.926941] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[66303.926967] CR2: 0000000000000000 CR3: 000000011ac20002 CR4: 00000000007706e0
[66303.926999] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[66303.927029] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[66303.927060] PKRU: 55555554
[66303.927075] Call Trace:
[66303.927094] <TASK>
[66303.927111] ? __die+0x23/0x70
[66303.927140] ? page_fault_oops+0x171/0x4e0
[66303.927176] ? exc_page_fault+0x7f/0x180
[66303.927209] ? asm_exc_page_fault+0x26/0x30
[66303.927244] ? ice_get_ringparam+0x22/0x50 [ice]
[66303.927433] rings_prepare_data+0x62/0x80
[66303.927469] ethnl_default_doit+0xe2/0x350
[66303.927501] genl_family_rcv_msg_doit.isra.0+0xe3/0x140
[66303.927538] genl_rcv_msg+0x1b1/0x2c0
[66303.927561] ? __pfx_ethnl_default_doit+0x10/0x10
[66303.927590] ? __pfx_genl_rcv_msg+0x10/0x10
[66303.927615] netlink_rcv_skb+0x58/0x110
[66303.927644] genl_rcv+0x28/0x40
[66303.927665] netlink_unicast+0x19e/0x290
[66303.927691] netlink_sendmsg+0x254/0x4d0
[66303.927717] sock_sendmsg+0x93/0xa0
[66303.927743] __sys_sendto+0x126/0x170
[66303.927780] __x64_sys_sendto+0x24/0x30
[66303.928593] do_syscall_64+0x5d/0x90
[66303.929370] ? __count_memcg_events+0x60/0xa0
[66303.930146] ? count_memcg_events.constprop.0+0x1a/0x30
[66303.930920] ? handle_mm_fault+0x9e/0x350
[66303.931688] ? do_user_addr_fault+0x258/0x740
[66303.932452] ? exc_page_fault+0x7f/0x180
[66303.933193] entry_SYSCALL_64_after_hwframe+0x72/0xdc |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: verify orphan file size is not too big
In principle orphan file can be arbitrarily large. However orphan replay
needs to traverse it all and we also pin all its buffers in memory. Thus
filesystems with absurdly large orphan files can lead to big amounts of
memory consumed. Limit orphan file size to a sane value and also use
kvmalloc() for allocating array of block descriptor structures to avoid
large order allocations for sane but large orphan files. |
| In the Linux kernel, the following vulnerability has been resolved:
rxrpc: Fix timeout of a call that hasn't yet been granted a channel
afs_make_call() calls rxrpc_kernel_begin_call() to begin a call (which may
get stalled in the background waiting for a connection to become
available); it then calls rxrpc_kernel_set_max_life() to set the timeouts -
but that starts the call timer so the call timer might then expire before
we get a connection assigned - leading to the following oops if the call
stalled:
BUG: kernel NULL pointer dereference, address: 0000000000000000
...
CPU: 1 PID: 5111 Comm: krxrpcio/0 Not tainted 6.3.0-rc7-build3+ #701
RIP: 0010:rxrpc_alloc_txbuf+0xc0/0x157
...
Call Trace:
<TASK>
rxrpc_send_ACK+0x50/0x13b
rxrpc_input_call_event+0x16a/0x67d
rxrpc_io_thread+0x1b6/0x45f
? _raw_spin_unlock_irqrestore+0x1f/0x35
? rxrpc_input_packet+0x519/0x519
kthread+0xe7/0xef
? kthread_complete_and_exit+0x1b/0x1b
ret_from_fork+0x22/0x30
Fix this by noting the timeouts in struct rxrpc_call when the call is
created. The timer will be started when the first packet is transmitted.
It shouldn't be possible to trigger this directly from userspace through
AF_RXRPC as sendmsg() will return EBUSY if the call is in the
waiting-for-conn state if it dropped out of the wait due to a signal. |
| In the Linux kernel, the following vulnerability has been resolved:
mailbox: zynqmp-ipi: Fix SGI cleanup on unbind
The driver incorrectly determines SGI vs SPI interrupts by checking IRQ
number < 16, which fails with dynamic IRQ allocation. During unbind,
this causes improper SGI cleanup leading to kernel crash.
Add explicit irq_type field to pdata for reliable identification of SGI
interrupts (type-2) and only clean up SGI resources when appropriate. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: host: max3421-hcd: Fix error pointer dereference in probe cleanup
The kthread_run() function returns error pointers so the
max3421_hcd->spi_thread pointer can be either error pointers or NULL.
Check for both before dereferencing it. |
| In the Linux kernel, the following vulnerability has been resolved:
PM / devfreq: mtk-cci: Fix potential error pointer dereference in probe()
The drv->sram_reg pointer could be set to ERR_PTR(-EPROBE_DEFER) which
would lead to a error pointer dereference. Use IS_ERR_OR_NULL() to check
that the pointer is valid. |
| In the Linux kernel, the following vulnerability has been resolved:
net: do not allow gso_size to be set to GSO_BY_FRAGS
One missing check in virtio_net_hdr_to_skb() allowed
syzbot to crash kernels again [1]
Do not allow gso_size to be set to GSO_BY_FRAGS (0xffff),
because this magic value is used by the kernel.
[1]
general protection fault, probably for non-canonical address 0xdffffc000000000e: 0000 [#1] PREEMPT SMP KASAN
KASAN: null-ptr-deref in range [0x0000000000000070-0x0000000000000077]
CPU: 0 PID: 5039 Comm: syz-executor401 Not tainted 6.5.0-rc5-next-20230809-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 07/26/2023
RIP: 0010:skb_segment+0x1a52/0x3ef0 net/core/skbuff.c:4500
Code: 00 00 00 e9 ab eb ff ff e8 6b 96 5d f9 48 8b 84 24 00 01 00 00 48 8d 78 70 48 b8 00 00 00 00 00 fc ff df 48 89 fa 48 c1 ea 03 <0f> b6 04 02 84 c0 74 08 3c 03 0f 8e ea 21 00 00 48 8b 84 24 00 01
RSP: 0018:ffffc90003d3f1c8 EFLAGS: 00010202
RAX: dffffc0000000000 RBX: 000000000001fffe RCX: 0000000000000000
RDX: 000000000000000e RSI: ffffffff882a3115 RDI: 0000000000000070
RBP: ffffc90003d3f378 R08: 0000000000000005 R09: 000000000000ffff
R10: 000000000000ffff R11: 5ee4a93e456187d6 R12: 000000000001ffc6
R13: dffffc0000000000 R14: 0000000000000008 R15: 000000000000ffff
FS: 00005555563f2380(0000) GS:ffff8880b9800000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000020020000 CR3: 000000001626d000 CR4: 00000000003506f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
udp6_ufo_fragment+0x9d2/0xd50 net/ipv6/udp_offload.c:109
ipv6_gso_segment+0x5c4/0x17b0 net/ipv6/ip6_offload.c:120
skb_mac_gso_segment+0x292/0x610 net/core/gso.c:53
__skb_gso_segment+0x339/0x710 net/core/gso.c:124
skb_gso_segment include/net/gso.h:83 [inline]
validate_xmit_skb+0x3a5/0xf10 net/core/dev.c:3625
__dev_queue_xmit+0x8f0/0x3d60 net/core/dev.c:4329
dev_queue_xmit include/linux/netdevice.h:3082 [inline]
packet_xmit+0x257/0x380 net/packet/af_packet.c:276
packet_snd net/packet/af_packet.c:3087 [inline]
packet_sendmsg+0x24c7/0x5570 net/packet/af_packet.c:3119
sock_sendmsg_nosec net/socket.c:727 [inline]
sock_sendmsg+0xd9/0x180 net/socket.c:750
____sys_sendmsg+0x6ac/0x940 net/socket.c:2496
___sys_sendmsg+0x135/0x1d0 net/socket.c:2550
__sys_sendmsg+0x117/0x1e0 net/socket.c:2579
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x38/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
RIP: 0033:0x7ff27cdb34d9 |
| In the Linux kernel, the following vulnerability has been resolved:
Squashfs: reject negative file sizes in squashfs_read_inode()
Syskaller reports a "WARNING in ovl_copy_up_file" in overlayfs.
This warning is ultimately caused because the underlying Squashfs file
system returns a file with a negative file size.
This commit checks for a negative file size and returns EINVAL.
[phillip@squashfs.org.uk: only need to check 64 bit quantity] |
| Improper input validation in the Linux kernel-mode driver for some Intel(R) 700 Series Ethernet before version 2.28.5 may allow an authenticated user to potentially enable escalation of privilege. |
| In the Linux kernel, the following vulnerability has been resolved:
md: fix warning for holder mismatch from export_rdev()
Commit a1d767191096 ("md: use mddev->external to select holder in
export_rdev()") fix the problem that 'claim_rdev' is used for
blkdev_get_by_dev() while 'rdev' is used for blkdev_put().
However, if mddev->external is changed from 0 to 1, then 'rdev' is used
for blkdev_get_by_dev() while 'claim_rdev' is used for blkdev_put(). And
this problem can be reporduced reliably by following:
New file: mdadm/tests/23rdev-lifetime
devname=${dev0##*/}
devt=`cat /sys/block/$devname/dev`
pid=""
runtime=2
clean_up_test() {
pill -9 $pid
echo clear > /sys/block/md0/md/array_state
}
trap 'clean_up_test' EXIT
add_by_sysfs() {
while true; do
echo $devt > /sys/block/md0/md/new_dev
done
}
remove_by_sysfs(){
while true; do
echo remove > /sys/block/md0/md/dev-${devname}/state
done
}
echo md0 > /sys/module/md_mod/parameters/new_array || die "create md0 failed"
add_by_sysfs &
pid="$pid $!"
remove_by_sysfs &
pid="$pid $!"
sleep $runtime
exit 0
Test cmd:
./test --save-logs --logdir=/tmp/ --keep-going --dev=loop --tests=23rdev-lifetime
Test result:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 960 at block/bdev.c:618 blkdev_put+0x27c/0x330
Modules linked in: multipath md_mod loop
CPU: 0 PID: 960 Comm: test Not tainted 6.5.0-rc2-00121-g01e55c376936-dirty #50
RIP: 0010:blkdev_put+0x27c/0x330
Call Trace:
<TASK>
export_rdev.isra.23+0x50/0xa0 [md_mod]
mddev_unlock+0x19d/0x300 [md_mod]
rdev_attr_store+0xec/0x190 [md_mod]
sysfs_kf_write+0x52/0x70
kernfs_fop_write_iter+0x19a/0x2a0
vfs_write+0x3b5/0x770
ksys_write+0x74/0x150
__x64_sys_write+0x22/0x30
do_syscall_64+0x40/0x90
entry_SYSCALL_64_after_hwframe+0x63/0xcd
Fix the problem by recording if 'rdev' is used as holder. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: handle case when repair happens with dev-replace
[BUG]
There is a bug report that a BUG_ON() in btrfs_repair_io_failure()
(originally repair_io_failure() in v6.0 kernel) got triggered when
replacing a unreliable disk:
BTRFS warning (device sda1): csum failed root 257 ino 2397453 off 39624704 csum 0xb0d18c75 expected csum 0x4dae9c5e mirror 3
kernel BUG at fs/btrfs/extent_io.c:2380!
invalid opcode: 0000 [#1] PREEMPT SMP NOPTI
CPU: 9 PID: 3614331 Comm: kworker/u257:2 Tainted: G OE 6.0.0-5-amd64 #1 Debian 6.0.10-2
Hardware name: Micro-Star International Co., Ltd. MS-7C60/TRX40 PRO WIFI (MS-7C60), BIOS 2.70 07/01/2021
Workqueue: btrfs-endio btrfs_end_bio_work [btrfs]
RIP: 0010:repair_io_failure+0x24a/0x260 [btrfs]
Call Trace:
<TASK>
clean_io_failure+0x14d/0x180 [btrfs]
end_bio_extent_readpage+0x412/0x6e0 [btrfs]
? __switch_to+0x106/0x420
process_one_work+0x1c7/0x380
worker_thread+0x4d/0x380
? rescuer_thread+0x3a0/0x3a0
kthread+0xe9/0x110
? kthread_complete_and_exit+0x20/0x20
ret_from_fork+0x22/0x30
[CAUSE]
Before the BUG_ON(), we got some read errors from the replace target
first, note the mirror number (3, which is beyond RAID1 duplication,
thus it's read from the replace target device).
Then at the BUG_ON() location, we are trying to writeback the repaired
sectors back the failed device.
The check looks like this:
ret = btrfs_map_block(fs_info, BTRFS_MAP_WRITE, logical,
&map_length, &bioc, mirror_num);
if (ret)
goto out_counter_dec;
BUG_ON(mirror_num != bioc->mirror_num);
But inside btrfs_map_block(), we can modify bioc->mirror_num especially
for dev-replace:
if (dev_replace_is_ongoing && mirror_num == map->num_stripes + 1 &&
!need_full_stripe(op) && dev_replace->tgtdev != NULL) {
ret = get_extra_mirror_from_replace(fs_info, logical, *length,
dev_replace->srcdev->devid,
&mirror_num,
&physical_to_patch_in_first_stripe);
patch_the_first_stripe_for_dev_replace = 1;
}
Thus if we're repairing the replace target device, we're going to
trigger that BUG_ON().
But in reality, the read failure from the replace target device may be
that, our replace hasn't reached the range we're reading, thus we're
reading garbage, but with replace running, the range would be properly
filled later.
Thus in that case, we don't need to do anything but let the replace
routine to handle it.
[FIX]
Instead of a BUG_ON(), just skip the repair if we're repairing the
device replace target device. |
