Search
Search Results (6 CVEs found)
| CVE | Vendors | Products | Updated | CVSS v3.1 |
|---|---|---|---|---|
| CVE-2026-93184 | 1 Linux | 1 Linux Kernel | 2026-09-19 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: ASoC: fsl_audmix: rework runtime PM handling in probe After pm_runtime_enable() the AUDMIX block is powered off and stays suspended until the first runtime resume. Register writes issued between probe() and the first resume (e.g. from DAPM or ALSA control paths) target unpowered hardware and cause a system hang. Fix this by calling pm_runtime_resume_and_get() immediately after pm_runtime_enable() to power the hardware up and enable its clocks. Release the reference afterwards with pm_runtime_put() to allow the runtime PM framework to suspend the device and switch the regmap to cache-only mode when idle. When CONFIG_PM is disabled or runtime PM is not enabled, pm_runtime_* calls are stubs that do not power up the hardware. Handle this case explicitly by calling fsl_audmix_runtime_resume() directly so the hardware is always initialised and its clocks are enabled, ensuring register accesses succeed regardless of PM configuration. | ||||
| CVE-2026-90390 | 1 Linux | 1 Linux Kernel | 2026-09-19 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: md/bitmap: resume array on backlog_store() error path backlog_store() suspends the array before checking whether a write-mostly device exists. If no such device exists, the error path only unlocks reconfig_mutex and leaves the array suspended, blocking subsequent I/O. Use mddev_unlock_and_resume() to release both states. | ||||
| CVE-2026-89949 | 1 Linux | 1 Linux Kernel | 2026-09-18 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: batman-adv: dat: avoid unaligned fault in IP extraction Independent of the alignment of the ARP packet in the SKB, either the batadv_arp_ip_src or the batadv_arp_ip_dst will have an unaligned access (on HW without native unaligned read support). Use get_unaligned() to handle this properly on all architectures. | ||||
| CVE-2026-80856 | 1 Linux | 1 Linux Kernel | 2026-09-04 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: fuse: fix invalidate lock leak on setattr writeback failure fuse_do_setattr() takes filemap_invalidate_lock() for a DAX truncate (fault_blocked = true) and releases it at the out:/error: labels. But when a writeback flush is also needed, a write_inode_now() failure returns directly and leaks the lock, so any later fault or truncate on the file stalls on the stale rwsem. For example, truncate(2) on a setuid file reaches fuse_do_setattr() with both ATTR_SIZE and ATTR_MODE set: truncate(2) └─ do_truncate() ├─ dentry_needs_remove_privs() # S_ISUID └─ notify_change() # KILL_SUID -> ATTR_MODE └─ fuse_setattr() # no killpriv: │ # ia_valid |= ATTR_MODE └─ fuse_do_setattr() ├─ filemap_invalidate_lock() # IS_DAX && is_truncate └─ write_inode_now() # is_wb && ATTR_MODE └─ if (err) # e.g. daemon -> -EIO return err # <- lock leaked Fix this by adding an unlock label that releases the lock before returning the error, and use it for the fuse_dax_break_layouts() failure path as well. | ||||
| CVE-2025-30075 | 2 Microsoft, Mindmanager | 2 Windows, Mindmanager | 2026-04-15 | 2.2 Low |
| In Alludo MindManager before 25.0.208 on Windows, attackers could potentially execute code as other local users on the same machine if they could write DLL files to directories within victims' DLL search paths. | ||||
| CVE-2024-56625 | 1 Linux | 1 Linux Kernel | 2025-11-03 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: can: dev: can_set_termination(): allow sleeping GPIOs In commit 6e86a1543c37 ("can: dev: provide optional GPIO based termination support") GPIO based termination support was added. For no particular reason that patch uses gpiod_set_value() to set the GPIO. This leads to the following warning, if the systems uses a sleeping GPIO, i.e. behind an I2C port expander: | WARNING: CPU: 0 PID: 379 at /drivers/gpio/gpiolib.c:3496 gpiod_set_value+0x50/0x6c | CPU: 0 UID: 0 PID: 379 Comm: ip Not tainted 6.11.0-20241016-1 #1 823affae360cc91126e4d316d7a614a8bf86236c Replace gpiod_set_value() by gpiod_set_value_cansleep() to allow the use of sleeping GPIOs. | ||||
Page 1 of 1.